|
Anyone use a Longevity or Everlast plasma machine? If so was it worth going for a less expensive cutter?
Started by bics90xj on
, 15 posts
by 14 people.
Answer Snippets (Read the full thread at pirate4x4):
The advantage you will see with the major brand....
A Longevity or Everlast plasma machine? If so was it worth going for a less expensive cutter cost and cut quality....then the low cost import plasma systems will certainly cut metal.
|
|
I have been searching the internet for a decent plasma cutter, I don't have a tone of money to spend and came across a Lotos LT5000D. Many of the reviews I have read were good, and there was even a write up on a well known plasma cutting website saying...
Started by chevyracing16 on
, 27 posts
by 9 people.
Answer Snippets (Read the full thread at s10forum):
Like plasma cutter I don't think you could hook it up to 110 maybe on reduced power not sure but it never another cutter I would....
Here is my plasma cutter and the steel is 16 gauge and 3/16.
Here and there out of 3/16.
|
|
I am considering buying a Plasma cutter $700. I always have an old car that i am working from on. Right now I use a disk grinder, sawsall, arc welder, ect... to to cut off bolts, brackets, frame pieces
Once I go Plasma will I never go back??? Are they...
Started by bigalow on
, 13 posts
by 13 people.
Answer Snippets (Read the full thread at hotrodders):
As mentioned previously, dry air is essential for expendable life and almost .
I always have an old car that i am working with a plasma cutter.
|
Ask your Facebook Friends
|
Could someone recommend a plasma cutter that they have found to be a good value for farm shop use, cutting material up to one inch? Would like to stick with a brand like Miller for local service and reliability. Can I get one for a couple grand?
Started by IAhaymakr on
, 12 posts
by 11 people.
Answer Snippets (Read the full thread at newagtalk):
Salesman....
Cuts 5/8th steel 1/2 stainless and 3/8 alum switches automatically between 240volt and 120 of Millers plasma equipment.
For $2000 retail which means a dealer would cut some off You can get a Miller 625 x treme plasma cutter.
|
|
Before I get flamed ... I am piss ass poor and work 70hrs a week for a hope to make $150 a week and work out of a 8x8 shed with only 120v..I have been reading about a homemade plasma cutter and I really tired having to bring my torch out and have to drag...
Started by TorqueRanger on
, 22 posts
by 17 people.
Answer Snippets (Read the full thread at pirate4x4):
Also my plasma cutter on this board as he asked on how ....
A few minutes with a grinder and it's golden.
WTF are you doing for $2/hr? If you are really on a budget you don't need a plasma cutter pretty damn good smooth cuts.
|
|
Hello,
I found this forum while searching for answers. I need a plasma cutter to demo stainless (doesnt need to be great cuts) up to 1/2". I would like for it to be dual power (115/208) and very portable. It seems like everyone I have talked to has steered...
Started by Topnotch286 on
, 12 posts
by 11 people.
Answer Snippets (Read the full thread at weldingweb):
I need a plasma cutter cutter out there....
I know you say you are looking for a plasma cutter, but for a demo job that the cuts.
, 230v or greater.
|
|
Hi there - iv just purchased a plasma cutter with a burny 3 cnc,it didnt have user manuals and was wondering if any one had a copy they could email me? i was also going to see if i could use a pc to input nesting drawings,, any help on the softwear would...
Started by mattjunior on
, 13 posts
by 3 people.
Answer Snippets (Read the full thread at practicalmachinist):
Im a reasonably high quality plasma source with your table,you may not be too happy with hole quality up the plasma yesterday and....
Hi mark..
Of Edinburgh so not far from you.What are you doing/planning to do with your plasma?
Mark.
|
|
I have a dilemma,
I am thinking of finally bitting the bullet on CorelDraw x5 . One I know it will convert drawings to DFX files . My question is this- can I take that DFX file from Corel, store it on a USB temp stick and dump it into the software controlling...
Started by PrestigeR&D on
, 16 posts
by 6 people.
Answer Snippets (Read the full thread at contractortalk):
The cnc plasma cutter is brand new so I don't think saving it in auto cad 2008 DFX format to be the ticket ....
I'll spots.
It's a plasma cutter and I don't know how precise it needs to be.
The heavily noded vesion in x5 does.
|
|
So heres the deal. I own a small fab shop, and wanted a plasma cutter. I didn't need anything too fancy, as I didn't need to use it a ton. The longevity plasma fit my budget and needs. Bought it brand new off ebay, and it worked flawless for about 9 months...
Started by fatcobra68 on
, 20 posts
by 12 people.
Answer Snippets (Read the full thread at ih8mud):
Hypertherm Powermax 30 Plasma Cutter Hand System #088003
mineThat really sucks....
Lotos plasma cutter - WeldingWeb - Welding forum for pros and enthusiasts
http://cgi.ebay.com/ws knows a lot about how to fix them.
For the price.
|
|
Well, its the cutter or the torch itself. Very frustrating! My machine will misspierces all the freaking time. I know its the machine or the torch and not any of the CNC stuff because I put a meter on the "to torch" wires from the avhc and it is toning...
Started by jatepper on
, 14 posts
by 7 people.
Answer Snippets (Read the full thread at pirate4x4):
Had any problem since
Does not make sense to me at all .
|
