|
Any Black Powder Enthusiasts? I've never gotten into it. I have never fired a black powder weapon but I do own a pistol.
I've been offered a replica of a Hawken .50 black powder for 50 bucks. If I buy it I want to get into it.
Someone tell me about it...
Started by Hostile on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at cowboyszone):
Cheapest one I....
If I buy as it is in good condition.
I've been offered a replica of a Hawken .50 black powder for 50 bucks.
I have never fired a black powder weapon but I do own a pistol.
|
|
How to Verify Powder Charge for Horn. LnL? How can I set up my hornady lnl press to verify the proper amount of powder? I can use the powder-cop die but would like a buzzer, if possible. Please provide some ideas.
Started by Uncle Richard on
, 20 posts
by 13 people.
Answer Snippets (Read the full thread at thehighroad):
Like to set one up with an alarm in case of a double... .
Found: : Richard (Post 8132087) i need a safety check such as the hornady powder cop die.
Like to set one up with an alarm in case of a double charge or low powder.
powder cop die.
|
|
Why can't somebody build a modern muzzle-loading firearm that uses smokeless powder?
Is there any scientific reason why muzzle-stuffers have to use that highly corrosive black powder, which is banned at all indoor ranges and even some outdoor shooting...
Started by GunnSmokeer on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at gon):
Black powder cause i like the puff and sparks and i like the smell !!! Savage makes one already and whole experience of connection to the past is what black powder shooting is about and is what guns, I use BH-209 for powder, and ....
|
Ask your Facebook Friends
|
Cleanest, most accurate, most versatile powder for revolver cartridges... Hi Folks,
I've got a bit more than half a pound each of HP38 and Universal that I'm working on using up loading my wheelgun calibers, .38spl, .357mag, .44spl, .44mag., and .45 Colt...
Started by Dadsnugun on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at defensivecarry):
If I had to make a single powder suffice for every handgun cartridge I reload then the choice would have to be Unique or other....
Bought powder, the selection should be better than it used to be!
Why would it be a tough sell the load.
|
|
Has anyone on here ever added aluminum or Stainless powders to an epoxy mix? I'm looking at using this as a potting mixture as I've decided doing the same job w/ 'store bought' industrial epoxy's are just to darn much money for what I want from them. ...
Started by JerryFlyGuy on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at cnczone):
Btw, have you ever imported aluminum powder? I understand....
Jer try www.shopmaninc.com for epoxy,$40 to$50US/gal
Google search Fine powder america, every type to do the job, how much stainless powder would this take? I have no idea..
|
|
East Coast Powder vs. West Coast BTH? (Repost) Well, seem to have lost the thread since it was posted after the backup had, so here it is again... Please any input on either is welcome.
I am familiar with East Coast Powder and from what I got out of the...
Started by Pdotizzle on
, 30 posts
by 24 people.
Answer Snippets (Read the full thread at opiophile):
West know than the devil you don't Re:....
Re: East Coast POWdER vs.
West Coast BTH? (Repost) I have never tried powder but when I was using I would score fire dope and with a tolerance couldn't do a .1 shot.
Re: East Coast POWdER vs.
|
|
What are the Top 3 powders used for reloading the .223.
I am talking about accuracy results. IE: what are the benchrest shooters using??
Plinking and cost do not count - I want 1/2" or less groups at 100YDS
Thanks JD
Started by C7AR15 on
, 15 posts
by 14 people.
Answer Snippets (Read the full thread at thefiringline):
I have found that changing the powder load and seating depth can make almost any powder shoot better....
Of course, the stock/barrel reaction to accuracy for your rifle .
Burning powder so that burn can extend all the way to the muzzle.
|
|
Looking for some advise. Reloading 9mm for plinking, was wondering what you all liked for a powder. No fighting please. Just looking for most loads per can and price. Thanks
Started by Mpape on
, 20 posts
by 19 people.
Answer Snippets (Read the full thread at gunloads):
I traded into a 8 lb can of a weird French powder
that is only Winchester Auto-Comp powder with....
For 9mm, tough ones like Bulleye and Titegroup.
Buy on performance.
COnsider powder is the cheapest part of any handgun load.
|
|
I have a frame in need of refinishing. Powder coating seems the most reasonably-priced option, but can anyone recommend a place to get this done, preferably near York?
Thanks in advance.
Started by Tewdric on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at yacf):
No doubt about it, that is....
I am thinking of commissioning job, IME.
I bought the Paul Donohue frame from, the names of not one, but two companies that do powder coating in M'bro is Shelby Arts, does powder coating and custom paint jobs.
|
|
Alright. Got my wheels powder coated monday by Mark Jurnigan in Plant City, FL. After that I took it upon myself to make my bowties match and scratch the little bit of red off that was left on my front RS badge. Hope you like it!
Started by BryanGoodson on
, 16 posts
by 10 people.
Answer Snippets (Read the full thread at camaro5):
Enjoy the ride....
Have you thought about blacking out the bezels? I have for powder coating.
Blue is my color.
Have you thought about blacking out Car look tough as hell.
Blue is my color.
Great! Love the banner Car look tough as hell.
|
