|
I see many, many threads pop up on how to go about doing a clutch job on our Tiburons with similar questions:
[1] What can I expect from a clutch install job?
[2] How does things look like in a clutch job?
[3] How do I remove the throw-out bearing (TOB...
Started by optimummind on
, 18 posts
by 15 people.
Answer Snippets (Read the full thread at newtiburon):
Http://www.youtube.com/watch?v the piston falls out....
Glad i seen this and not make the mistake of installing the throw out bearing job on our Tiburons, which utilizes a pull-type clutch system.
Performed a pull type clutch.
|
|
I am converting a 2003 WRX transmission from pull clutch to push clutch. The release fork on the pull clutch transmission is much stronger than the sheet metal fork used on the push clutch transmission. I am using a Wilwood pull slave cylinder to change...
Started by Heater Guy on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at nasioc):
Push style clutch the only way is to put the gears in the push case.
|
|
When you shift a motorcycle do you have to pull clutch lever all the way? Our can you pull it half way just before grabbing point?
Started by Timothy John on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at yahoo):
On most bikes that is around halfway or less.....
Bikes have a constant mesh only have to pull the clutch back beyond the engagement point of the clutch.
YOU are correct you do not pull the clutch lever in all the way...
|
Ask your Facebook Friends
|
Noticted today sitting at the lights with the clutch pulled up to my fingers the bike trys to still pull forward
I assume this is the clutch cable being a bit slack
I know there is an adjuster on the lever.
My question is am I right in asumming its the...
Started by Shaun 1WD on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at perthstreetbikes):
If you run out adjustment in the lever takeup and still have the clutch 'dragging' you'll clock wise and now all good....
No sweat.
The clutch cable is suppose to have slack, enough...
You've told us nothing, leaving us guessing.
Clockwise.
|
|
I planned on adding an extra plain plate to the clutch package to lessen the pull needed on the clutch. I had a plain plate ground down to 0.065" but it is still a bit thick to get the pressure plate and circlip installed. Question - would there be much...
Started by GeorgeJM on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at britbike):
Not so much to lessen the pull....
Ndnsclutch.htm Dynodave,
I assume I have the early clutch as the bike is a 1971 but didn't pull out and that helped lessen the force needed to pull the clutch, but, it's still pretty tight.
|
|
Pulling out of gear w/o clutch. Normal?
I've had my 2011 WRX for just over six months now and just noticed that I am able to pull it out of gear into neutral without using the clutch. I can do this with very little force (re: regular shifting force). ...
Started by SpekN9ne on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at clubwrx):
The sequence is something like: off the gas under slight pull on the stick, down with the clutch....
There is nothing wrong with that, and I actually do this in normal driving all the time .
Can pull it out of gear with no resistance.
|
|
I gotta 84 fxr with a primo pro clutch and a hydroalic set up.Pulling in the clutch lever is so hard it keeps blowing seals on the piston at the hadle bars.
I swapped out the dia. spring for the wimpiest one I can find and I adjusted the clutch primo'...
Started by hotrod1 on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at v-twinforum):
How long have you had this problem?, was there anything done before it started. .
|
|
Alright this is my last problem that I was hoping I would solve while fixing my other problems but it's not the case. When I accelerate hard in first it's pulling all the way to redline but when I shift in second and almost floor it the rpms shoot up ...
Started by Mjeezy11 on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at mazda6club):
Oh ok thanks for the help! Any suggestions on what clutch I should look at within a reasonable price?? Since its slips only when u accelerate hard off the....
Eventually, it will happen at all rpms and become undriveable .
Clutch is slipping.
|
|
Hi guys!!
Managed to get my ABF swap done last week, Ran it over the weekend, including Castle Combe Saturday!!
Only problem I've got, I did this to the first clutch within 10 miles...
Ok ok, so maybe I had over adjusted it a touch...
So I fitted another...
Started by Norledge on
, 11 posts
by 10 people.
Answer Snippets (Read the full thread at com):
Got a pic of the other side? I've not had anyone report a problem burning it out? what make of clutch....
Had same setup in my mk2 abf on 020 16v box with hotgolf lightend flywheel and sachs clutch and had in and the clutch is still like new.
|
|
Hi fellow forum users! I've just registered with the site due to a strange problem with my bike.
First off, I ride a 1995 Savage with about 15,600 miles on it.
Oil, air filter and spark plug changed just before 15,000.
The last couple times I've ridden...
Started by mgum47 on
, 8 posts
by 5 people.
Answer Snippets (Read the full thread at suzukisavage):
I assume it's the huge nut on the first picture here?:
http://suzukisavage... .
I'll check when I've got daylight.
Thanks.
Real tight.
It has to be tight...
Check the drive pulley nut.
Right side or left? Most likely the left side, but it was hard for me to tell .
|
