|
Hi, am preparing to renew the timing belt on our year 2000 Mondeo. I have the Haynes Service & Repair Manual #1923 which is very good but does not seem to include the torque wrench setting for the crankshaft pulley bolt. Does anyone have the correct setting...
Started by kiriath-arba on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at automotiveforums):
|
|
So a few days ago my crank pulley started to wobble like mad. I drove it 15 miles home and stopped driving it since. At higher rpm's the car was running like usual.
I assumed that the crank pulley bolt came loose so I purchased the tool for the crank ...
Started by fourthgeneration on
, 18 posts
by 13 people.
Answer Snippets (Read the full thread at preludeonline):
I hope you'll be able to resolve you're crank pulley....
The alternator belt was hanging around the pulley..
Took out my power steering belt but..
Except the crank pulley bolt was loose as well...
As well around November of last year...
|
|
After a decent high power 1/2" drive air operated impact wrench, whats good these days? i have seen the snap on MG725 with 810 ft lb of recommended working torque which sounds great, what other wrenches are worth a look? and whilst on the subject of impact...
Answer Snippets (Read the full thread at kelsey-forums):
Undo a crank pulley bolt once with it, my mate used his impact wrench and it undone the bolt.
|
Ask your Facebook Friends
|
Posted Today, 01:42 PM
Hi,
I'm looking to see if anyone has an old Deore XT 9 speed pulley or pulley set or something that would fit. I am not picky, just want something that rolls and doesn't come loose once a week and break my chain while I'm riding...
Started by Mr. D. on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at stlbiking):
|
|
Is there any advantage that pass through has over a ratchet wrench? Any real reason to have a pass through and a ratchet wrenches?
See like ratchet wrench has the low profile cover vs the pass through and gives the same advantage they have over a regular...
Started by shoturtle on
, 14 posts
by 10 people.
Answer Snippets (Read the full thread at garagejournal):
A ratcheting wrench won't reach the nut, and the stud may be too long for a deep socket.
I'm going to have both the pass through and normal square I encounter a nut that's recessed .
Ratchet for when I need a torque wrench.
Related shopping results:
|
|
Is anybody using any of those cordless/corded impact wrenches instead of pneumatic ones?
How do they compare to each other? Are they worth buying?
Started by celsoglima on
, 20 posts
by 12 people.
Answer Snippets (Read the full thread at explorerforum):
It with the breaker bar switching between the two when the wrench just couldn't break it loose its time a gasoline powered impact wrench: http://www.magnum-usa.com/equip2.html http://toolmonger.com/2007/04/16/a-g...impact-wrench/....
|
|
Kllutch 24v
Titan 24V Cordless Impact Wrench 280 FT/LB
Good Year 24V Cordless Impact Wrench 1/2" Drive 200 FT/LB
LONGACRE CORDLESS PIT IMPACT WRENCH,24 VOLT 300 FT/LB
NEIKO 24 VOLTS CORDLESS IMPACT WRENCH 350 FT/LB
KOBALT 20V Impact Wrench 300 FT/LB
Let...
Started by PathfinderDude on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at hotrodders):
It wasn't cordless but I wouldn't buy with a Craftsman electric impact wrench....
Log home with a Craftsman electric impact wrench.
Quote sq.
Don't get anything here, go to Consumer Reports or Google Cordless Impact Wrench Reviews.
|
|
How do i get my crank pulley off of my b20a??
Started by BASED on
, 25 posts
by 11 people.
Answer Snippets (Read the full thread at preludepower):
It took me I was forced to take it to my mechanic... .
Once the nut is removed, put both hands around the pulley and wiggle it while pulling out at yourself.
You've got to break the crank pulley nut free and then pull the pulley off evenly.
|
|
" This is a complete DIY installation guide for the 3 piece NST kit from NST - NonStopTuning "
NST PART NUMBER: NST21915KIT
NST - The Leader In 8th Gen Civic Pulleys
1.- park your car and make sure you have room to play whit the car
2.- jack up the car...
Started by el_ben2 on
, 20 posts
by 10 people.
Answer Snippets (Read the full thread at 8thcivic):
Great job el ben2 I have these pulleys on mine and they kick ass, I would recommend.
7-10 HP is awesome from just pulley's.
But hell, I might pick some up when I get my bonus .
pulley's were that high...
|
|
The crank pulley fell off and wore through the timing cover. I need to know what size of bolt i need to put back in the pulley. I think some handy jb weld will take care of the timing cover. by the way this car has 312k miles on it!
Answer Snippets (Read the full thread at legacygt):
This has....
The timing belt was done and whatnot.
It will still be able to be removed and reinstalled when necessary .
The crank pulley,
crank gear behind the pulley and the
woodruff key (the half moon shaped one that the pulley made.
|
