|
I've found a bit of rust scattered all over my car, none on the usual spots like the wheel wells and whatnot, but the undersides of the floor pans have pretty rough surface rust.
So I'll list the places the car has rust
The whole underbelly has surface...
Started by Dead Reckon on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at thirdgen):
I had rust on the hatch....
Hatch rust may be able to be sanded and fixed, or may classes.
Hatch rust:
Leak, mysterious bondo-like substance in spare tire well:
Leak:
Rest of the pictures posted here you have nothing out of the ordinary.
|
|
How to remove rust from chrome This trick will remove rust from chrome.
I just found this out on another site. I wanted a cheap way to remove a little rust spot from my truck's bumper.
You get a piece of aluminum foil and dip it into some Coca Cola. Rub...
Started by Windwalker7 on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at motorcycleforums):
And be careful when using.
Something amazing.Only Aluminum foil and some Coca Cola can really remove rust in no time.I will trythat rust isn't to bad - if it's bad, then muriatic acid is required.
|
|
Hey Guys,
I have a question;
What your opinion on Por15 and other rust delete??
Thank you.
-Y.
POR15 - (I know it good) - Starter pack you'll get a 4 oz. can of POR-15 (enough to cover 12 square feet) :
LocTite - Rust-Oleum Automotive rust removal package...
Started by 1-ev.com on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at pelicanparts):
rust mort changes rust to a black inert substance, but you have to get the majority of the rust off....
It bonds to rough surfaces, especially in the sun.
It just "encapsulates" it.
PO15 does not delete rust.
Hands btw, sticks.
|
Ask your Facebook Friends
|
Ok PSB brains trust. What's the best way to remove little specks of surface rust from swingarms, triple clamps etc?
CLR clear? Sandpaper? A scourer? Piss on it?
Started by resist on
, 17 posts
by 14 people.
Answer Snippets (Read the full thread at perthstreetbikes):
Next best? Rub with scourer/sandpaper until all evidence of rust has....
Maybe just use a little rust converter before trying sandpaper, ooo and angle grinder will do (depending upon thickness of metal and level of rust) and refinish.
|
|
Cleaning down my rifle noticed tiny lil specs of rust colour on certain areas
I tried scrubbing down the area's with an oily rag and such but they didn't really remove them.
I always give the rifle a rub down with oily rag after use, what can I use to...
Started by Bigthug87 on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at pigeonwatch):
Plastic, When i'm rebluing any guns....
Hiya, When i'm rebluing any guns, I give it a good rub down with wire wool to remove the rust with wire wool to remove the rust specks use the fine stuff, it doesnt mark the gun at all...
|
|
I have some raw steel that I need to cut and paint. It has typical light surface rust from being stored at the supplier. What is the best method to remove and then paint? I hate to use a grinder, too rough. Light sandpaper in a sander might be OK. Or ...
Started by pinchvalve on
, 12 posts
by 11 people.
Answer Snippets (Read the full thread at grassrootsmotorsports):
I was wirewheeling rust and bondo off once.
The cup type brushes work good, the Scotchbrites do too but man they wear out QUICK .
Hours in vinegar will strip any rust and leave clean metal.
|
|
I've got a milling machine that was not used for quite a while and its table and scales are coated with rust. its not deep but its annoying. how can it be removed?
Thanx for your help.
Started by amron on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at chaski):
- Phil Precise surfaces are cleaned (by me is to get under skin of the rust and shave....
I have used a green Scotchbrite pad with BoeShield rust preventative, which works well a rust remover which works well, but I never used it.
|
|
I am slowly disassembling a very badly rusted Singer Mdl 99K machine. I do not know how it came to be so rusted but it was seized up tight. I have it freed up somewhat but I will have to totally strip it down to it's last part to totally clean the rust...
Started by J Miller on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at sewingforum):
Www.katedicey.co.uk
Click on Kate's Pages and explore! Kate,
The rust is more severe than a buffing.
|
|
This is interesting. Just found it on the Classic American site.
» How To Remove Rust From Classic Harley Gas Tank
Started by Any old iron on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at harley-davidson-hangout):
You now need to treat the steel with something (oil,grease,primer whatever) , as if its left in the air it will get surface rust again
The treacle mixture.
Of rust will be gone leaving only bare steel.
|
|
As I see various threads the thought came to me: what determines when a truck has to much rust to repair or restore. Example: If one one see a 50th Stepside or 50th Panel with lots of rust verses a common six cylinder LWB Stepside...would the 50th's be...
Started by 70cst on
, 16 posts
by 12 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
I personally don't care for rust be I....
It's actually much simpler than it appears, once you remove the equation of "what.
Of the salt belt states,might be worthy of just about any amount of rust repair.By the same token sense man.
|
