|
The clutch in the wagon is acting goofy all of a sudden. This morning the clutch pedal was very "loose", it starts engaging about half way down, and when I put it in gear and start to let off of the pedal the car starts moving when I have released the...
Started by txrealtor on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at bimmerfest):
Usually it into the bell housing....
Sent from my Desire HD using Bimmer App Sounds like slave cylinder seals may be bad .
Yeah it probably could be your slave cylinder or like he said needs to be bled again .
Clutch part , my bad.
|
|
I'm at my last wits with this one guys. I did the slave cylinder mod found here: http://www.newtiburon.com/forums/showthread.php?t=1962 and I wish I had never done this. Basically what's happening now is my car is slipping so hard, as if I'm just dumping...
Started by Lotus09 on
, 17 posts
by 11 people.
Answer Snippets (Read the full thread at newtiburon):
It to the dealer? Tomorrow I'm going to put the stock slave cylinder back on, and taking it straightDid you accidentally put fluid in the brake master cylinder instead of the clutch master cylinder replaced the spring and ....
|
|
I have an 08 G37S with 43,800 miles on it. It's out of warranty, by time.
I've started leaking hydraulic fluid and had to fill up the clutch resevoir. Today I took it to Infinity. They told me that it's likely the slave cylinder and it's not covered under...
Started by RJ'sG37 on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at 6mt):
ENGINE - Cylinder heads and block and all internal parts.
From the warranty booklet.
Update! I'm getting a new transmission! At first they said they would replace the slave cylinder in the powertrain warranty.
|
Ask your Facebook Friends
|
So I haven't been driving my GTV much as of late, but I noticed the last few times I drove it after the latest track 'happy laps', the clutch pedal has a lot of free play at the top and the clutch disengages a lot closer to the floor than before. It still...
Started by DAL32 on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at ausalfa):
Cheap part to buy off and would become stuck, however the actuating rod from the slave cylinder will still return(somewhat the actuating rod from the....
Check your clutch reservoir for fluid level Slave cylinder on it's way out.
|
|
89 Blu 5-speed Slave Cylinder... OMG!
...so I've stripped the exhaust system off, I'll replace at least the shocks, upper and lower control arms in the front and not sure yet what to do with the rear end.
Great drive train notwithstanding the slave, ...
Started by Platoribs on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at tccoa):
I bought a Wagner from rockauto for 50 including shipping Slave cylinder's are in stock.
|
|
Hi everybody.
Alright here is a little story:
My neighbor has a 1994 BMW 525i 5 speed sedan. It is very nice. He had it for about two years and then parked it. I am not sure why. Then one day I went over and asked him if he could start it up and I take...
Started by KJ4YXY on
, 25 posts
by 5 people.
Answer Snippets (Read the full thread at bimmerforums):
Jack up the car, loosen the nut connecting the clutch line to the slave cylinder then remove the two 13mm nuts holding....
So save yourself some time and start with the slave 1st.
I have very rarely seen a master cylinder fail.
|
|
Hi,
Is this a concentric clutch slave cylinder ?
How do you remove the pipe from it ?
Will a 850r clutch fit with this slave cylinder ?
Started by oblark on
, 3 posts
by 2 people.
Answer Snippets (Read the full thread at volvot5):
The pipe meets the plastic of the slave cylinder you can see a small metal line you need a small flat cylinder just be careful not to brake the slave cylinder 1 yes that is a concentrick bearing 2 as above 3 screwdriver....
|
|
Where is it? My clutch sometimes doesnt come back up very fast / with much pressure, i had to lift it up with my foot once already. I need to bleed the cylinder or replace it right? but i CANT FIND IT uugh ive been looking on google and on my car for ...
Started by bangarang on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at performanceprobe):
Remove the plastic duct and flex bellows (10mm nuts) and lookFollow the hard line... .
By the way, am I right to bleed the slave cylinder cause i really hope thats all is is directly above the slave cylinder.
On the driver's side.
|
|
Morning all, after a bad week yesterday topped it off nicely, broke down in the morning at the road side after losing my clutch on my disco 300 tdi r reg, after a quick peek under i asumed my slave cylinder failed, after an hour wait got a lift and got...
Started by adie_sj on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at difflock):
Clutch fork??? you'll need to remove slave cylinder and look inside to see how far down clutch arm plan B cut out some small round card disks to slide over the rod to it sat central put slave cylinder to push the push rod ....
|
|
MT removal, clutch slave cylinder and clutch replacement
First, Im not sure if this is the right forum for this kind of thing so Mods feel free to move as appropriate.
On to the story Last Tuesday my clutch slave cylinder went out. I pushed the clutch...
Started by blueoval23 on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at focusfanatics):
Awesome write up....
I'm hoping to have the money saved to also get a LSD to install while the tranny is out for the clutch change .
It's not slipping, yet, but it's at the very top of the travel .
I have 138,000 miles.
Great write-up! I'm dreading this job.
|
