|
Where is the best place to buy home theater speaker wire? I'm rewiring my home theater equipment. And I need around 150 ft of speaker wire.
Started by gusamo on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at slickdeals):
Quote....
No, speaker wire quality doesn't convenient.
Does the speaker wire quality matter? I just got a new sound system and was wondering if i need to upgrade my wires too.
Of 14gauge for $12 (i think) plus shipping.
|
|
Will 12 Gauge speaker wire fit
Hello will will 12 Gauge speaker wire fit thru the door boots in a 2012 Focus? Thanks
Started by voipguy on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at focusfanatics):
Has anyone installed new speaker wire in there 2012 Focus, Just wondering or the other option....
So I just tied everything into the wires behind the radio.
Any speaker wire through it without doing some butchering to it.
|
|
Hello will will 12 Gauge speaker wire fit thru the door boots in a 2012 Focus? Thanks
Started by voipguy on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at focusfanatics):
Has anyone installed new speaker wire in there 2012 Focus, Just wondering or the other option....
So I just tied everything into the wires behind the radio.
Any speaker wire through it without doing some butchering to it.
|
Ask your Facebook Friends
|
Should I bi-wire my speakers?
Both my speakers (DLS R55 mk2) and amp Carat A57 mk2 are made to bi-wire but right now I use a Chord Odyssey 2 in single wire form and only bi-wire at the speaker end with a piece of Chord Oddysey 2 to the tredble.
Would...
Started by kristoffer on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at pinkfishmedia):
Would) and amp Carat A57 mk2 are ....
Would I get any form and only bi-wire at the speaker end with a piece of Chord Oddysey 2 to the tredble.
And only bi-wire at the speaker end with a piece of Chord Oddysey 2 to the tredble.
|
|
Wiring 2 speakers and sub to 1 amp Hey guys I have a 4 channel amp running a 12 inch sub in the boot of my VS. I would like to wire up the rear speakers to the amp as well, is this possible and how should I wire the speakers eg. In series or parallel?...
Started by spud_22 on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at justcommodores):
Share 3.08 LSD, 1.9.1 High Ratio Rockers, MACE CAI, Spacers Wire the 2 speakers to two channels and wire is should I ....
Are marked, but you might have to trace the wire back to the speaker to see which is which there.
|
|
Speaker ISO wiring I am trying to install my new comps but dont want to cut and slice up the oem connectors between the door and car.
Black lines are the new ones and red are the old ones that go through to the doors.
So which of the iso connectors at...
Started by john182rs on
, 14 posts
by 5 people.
Answer Snippets (Read the full thread at cliosport):
JustRe: Speaker....
Just be careful not to damage any of the nearby holes/pins .
A small allen key bit to work the holes big enough to pull speaker wire through,
then used a wire hanger the other, so split the speaker wire.
|
|
Just a quick question. Is wire like this 10m Loudspeaker Cable OFC 189 Strand Loud Speaker Wire | eBay any good?
Is it actually what it says it is OFC?
If so ill buy, sounds cheap
Started by bazzel on
, 25 posts
by 7 people.
Answer Snippets (Read the full thread at avforums):
Of QED 79 Strand 2.5mm² wire is about £17.50 for 10 meters -
QED 79 Strand Speaker Cable In Black Loud Speaker Wire | eBay
Sound too good? Looks the same as the 20m I bought a year ago from them on their webpage as well -
....
|
|
Reason for asking is, I run 12 awg wire for all my speakers. I was looking at a specific 7.2 wall plate at monoprice and the back side connectors for the sub (inside the wall) are not standard speaker bananas like the other speakers, but rather it is ...
Started by SBI on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at avsforum):
I agree that using speaker wire would allow unnecessary noise into the sub unless runs from the ....
You could probably connect your speaker wire to the center conductor.
To reduce the amount of noise coupled to the conductor .
|
|
Ok I have a 4x12 cab with 16 ohm speakers, How would I go about wiring these things so that they are 8 ohm? I found this...
Quote: : Now, if we take a single 8 ohm speaker and attach it to another 8 ohm speaker, we can actually hook it up so that its ...
Started by Halloween on
, 21 posts
by 8 people.
Answer Snippets (Read the full thread at gearslutz):
You could wire your 16 ohm cab as a stereo 8 ohm cab then you can it as a 16 ohm mono....
The single 8, or the 4 wired as 16....
Optimum...
To avoid damaging the amp, the speaker has to be the same, or higher impedance than the amp.
|
|
I added bass blockers to my door speakers today. I did this in my 02SS as well for my doors and rears as it takes out up to (for my application) 50w of bass from the speakers allowing much cleaner highs. I would ONLY suggest doing this if you are running...
Started by TAG UR IT on
, 25 posts
by 12 people.
Answer Snippets (Read the full thread at camaro5):
The ones I got block 0 to 300Hz into a 4-ohm speaker and 0-150Hz into a 8-ohm speaker that is 50 watts ....
FROM the amp to the speaker has at? There are different sizes.
Of the BA amp in the trunk, correct? Pretty sure that's right .
|
