|
I'm getting ready to change out my suspension front and rear. I've done my research (tons of info here &120) but I'm wondering if you guys have any tricks or special tools that you use to make the job go a little smoother.
Such as: Spring compressor: ...
Started by jdkilroy on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at toyota-4runner):
I just used a couple good blows with a hammer to separate the ball joint looking into getting heavy duty links)
I appreciate the tips, thanks air tools will help break open has less than 25k miles on it so I'm cautiously....
Nothing special needed.
|
|
Power torque tools.
Crank Pin.
The genuine tools for undoing the Power Torque crank pins are expensive.
You can make your own out of a couple of ordinary sockets for around $20 each. I used 3/8 sockets as thats the set i mainly use and thats what my torque...
Started by Rodeobob on
, 17 posts
by 9 people.
Answer Snippets (Read the full thread at outdoorking):
I bought a couple of "the right tool....
No way.
Special tools $87 each...
For these special tools, for the home handyman that likes to tinker (as we all like to do here)
being started fiddling with Victa PowerTorque Mowers.
|
|
A while back I searched for how to set the timing on the 54-degree 3.0L V6 Saturn L300 engine. All of the posts that I read referred to needing the special GM tool kit (to the tune of $300 or so). I've devised my own procedure for setting the timing (...
Started by CoJames on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at saturnfans):
" Be aware that there are two timing marks on each camshaft sprocket - be sure to... .
This should be made a sticky.
Anyways, great post.
I'll pay you to do mine! Where was this post when I did mine? LOL .
Great tutorial still mind boggling to say the least.
|
Ask your Facebook Friends
|
Advertise Here
Growing up in the big city over the years I met quite a few characters who could get you practically anything for the right price ,or you knew a friend of a friend. I was wondering, if you are caught with your pants down in the city when...
Started by goliath4407 on
, 20 posts
by 16 people.
Answer Snippets (Read the full thread at survivalistboards):
Has a Special Acquisition Specialist Shady and stolen goods should be a lot cheaper than new ones.
|
|
How to bend 10mm copper tubing into a coil without welder or special tools?
Started by bruvvamoff on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at yahoo):
I best guess is to try filling it with sand maybe and then wrap it might work .
But if you don't have one ...
A bending spring is most often used down the bore. .
|
|
Just found out about this website who sell special car tools for BMW,MERCEDES BENZ,AUDI,VOLKSWAGEN, and other European cars! They have pretty good price. I have already bought a BMW tool (BMW Fan Clutch Pulley Wrench Nut Removal Tool). It's decent quality...
Answer Snippets (Read the full thread at trustmymechanic):
I need some information on best tools at http://www.trustmymechanic....
I will check it out soon.
I will look up to it.
Automotive Specialty Tools stocks alot of the special service tools for the website.
Google earth, Google chrome etc.
|
|
Finally received all of my new suspension for the wagon but upon reading some how to threads, there are some suggestions about using special tools (yes the ones i.d. Parts recommended i purchase, but didnt) are any of these tools absolutely necessary ...
Started by 2hellWITHhybrids on
, 6 posts
by 6 people.
Answer Snippets (Read the full thread at 166):
Got mine through KD tools and then found one in my tool box I madeI did a suspension re-fresh earlier....
I had the tools needed none of the sets seem to have.
You get what you pay for.
But renting/owning Davebugs tool is worth it.
|
|
Finally received all of my new suspension for the wagon but upon reading some how to threads, there are some suggestions about using special tools (yes the ones i.d. Parts recommended i purchase, but didnt) are any of these tools absolutely necessary ...
Started by 2hellWITHhybrids on
, 6 posts
by 6 people.
Answer Snippets (Read the full thread at tdiclub):
Got mine through KD tools and then found one in my tool box I madeI did a suspension re-fresh earlier....
I had the tools needed none of the sets seem to have.
You get what you pay for.
But renting/owning Davebugs tool is worth it.
|
|
06 cbr 600rr..got my SI cage today, wondering if i need any special tools to get the job done or is it all basic allen and sockets?
Started by Jrose152 on
, 3 posts
by 2 people.
Answer Snippets (Read the full thread at 600rr):
I had to buy some allen wrenches because mine were too short .
I wondered the same thing before just needed long ass allen wrenches and basic socket set .
|
|
Special marketing tools
Our monthly promotion Banners and Landing Pages can be found in our Media Gallery section under the keywords: calendar.
Cheers,
Monika
Started by monika on
, 3 posts
by 2 people.
Answer Snippets (Read the full thread at casinoaffiliateprograms):
Cheers,
Monika Thanks for the update, Monika!
Any insight as to what creatives are performing the best,... .
Originally Posted by monika
Our monthly promotion Banners and Landing Pages can be found in our Media Gallery section under the keywords: calendar .
|
