|
Hello everyone, i need a little advice. I need to decide on a rear end. my truck stock had the little 1.9 in it, so I'm wondering what the rear end can take. I'm pretty sure its 4:10 ratio. I really want to be able to spin both wheels, so i was looking...
Started by Jhall650 on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at v8s10):
M-21 / 12 Bolt
viewtopic.php?f=2&t=28910
1985 S10 Budget Build - Stock 2.8 / Auto...For now straight and stock 87 S10 SCLB 5.3/200-4r under heavy construction If it's 88 or later, it should, or 4.10 posi 8.8 for probably less than....
|
|
WTB stock g80, or any stock carrier for 8.6" 10 bolt Buddy blew out stock g80, need to buy a stock carrier to put back in it. Dont care if its a locker or open diff as long as it works. Let me know what ya got 2000 Silverado 1500 Z71 ecsb- Heads/Cam/Intake...
Started by chvy=power on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at ls1truck):
Same question..? 01 Silverado pm sent! 2000 Silverado 1500 Z71 ecsb- Heads/Cam/Intake 5.7 ls1- 4L65e, stalled with 4.11 gears
2008 Sierra ecsb 2wd 5.3- tune, intake, exhaust, vette servo i got one too off my 08 but its open diff... .
I also have this...
|
|
W bolt M-17.JPG W left side.JPG W M-17.JPG W P1090865.JPG W right side.JPG W.JPG W rec.JPG W marks.JPG W m-17 (2).JPG W bomb, Kmark.JPG Have this piece w/ some refinishing, E over bomb 9-18 barrel, Everything E so far. The very small lettering on receiver...
Started by Jim Noeller on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at gunboards):
The stock was replaced at some point, though, since the clearance cut for the bolt handle cut for bolt handle, althought obivious stock has been replaced I think more likely here maybeNeeded to add this bolt picture....
|
Ask your Facebook Friends
|
I have a Borg Warner 9 bolt forsale out of my 87 iroc. It has approx 125k miles on it. The posi clutch packs are all the way bottomed out and has 3:23 gears. There was no bearing noise before i pulled it. No metal chunks in the fluid either. Just needs...
Started by chevelle600 on
, 25 posts
by 6 people.
Answer Snippets (Read the full thread at thirdgen):
The carrier and r/p i would do $60 plus shipping What would shipping: : The pbr's are off of ... .
What would you want for the 9 bolt carrier and ring/pinion shipped in US? The pbr's are off of a 10 bolt.
A 10 or 9 bolt.
|
|
Eisenmann has since 1988 been manufacturing top quality exhausts with full German TUV approval. Eisenmann systems feature an aggressive tone, and target the luxury European car owner who is proud of their car and want to be noticed.
The systems are made...
Started by GTM_Challenge on
, 22 posts
by 4 people.
Answer Snippets (Read the full thread at m3post):
To any Eisenmann Black Edition Muffler for a perfect match Black edition pipes now in stock! We guarantee low pricing on all Eisenmann systems Stock updated as of 4-21-11 Challenge X pipes in stock reduction
- Flanged design for ....
|
|
Ok, I cannot get any ARP 425's yet, back ordered for who knows how long!! So if I buy new OEM bolts (or do I even need to) from what I am finding doing searches is I can go up to 125 PSI on them? Is this ok?
Trip from Ohio to Texas coming up and I'll ...
Started by Quad Racer Dad on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at cumminsforum):
You get stock specs on them, only increase the ft-lb by 2-3 and give about 10 min in between each head bolt thats rated for alot more then stock but less then the arp 425's and you can pick them up them down more than stock....
|
|
Posted 08 February 2012 - 08:42 PM
If you owned a stock rem 700, or Ruger M77, Savage 110, etc. what would be the first or only upgrade you would make to improve accuracy? Not incuding scope options. Would you drop in a Timney trigger or make pillar bed...
Started by User on
, 13 posts
by 1 people.
Answer Snippets (Read the full thread at coueswhitetail):
Plus it's easy, trigger, bedded stock and....
What would be the first or only upgrade you would make bed the stock?
Drop in Timney is what I did and it improved my accuracy quite a bit.
A stock rem 700, or Ruger M77, Savage 110, etc.
|
|
Anybody know of a good way of determining if a 91 Isuzu pickup has a 10 bolt or 12 bolt rear axle besides pulling it apart and counting ring gear bolts? It had the 2.6 liter with the 4 speed auto, according to what I have found online that should mean...
Started by isuzu4.3 on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at planetisuzoo):
Not saying that the isuzu 10 bolt wasn't a decent axle' Chevy LUV....
The r/p is pretty strong on the 10 bolt be nice to have a solid foundation to start with.
If it has drum brakes, my bet is that it is a 10 bolt.
|
|
What is up guys I have some questions about my 10 bolt. 1st off it has 160K+ miles on it but has no problems, no noises or anything like that. I was wondering how much power you can put to a stock 10 bolt. It is sitting under my 99 T/A with factory 3....
Started by Faught on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at ls1tech):
My plans were Quote....
It is sitting under my 99 T/A with factory 3.23 gears .
My plans were to get some cnc you can put to a stock 10 bolt.
It is sitting under my 99 T/A with factory 3.23 gears .
To a stock 10 bolt.
|
|
For 300.00 OBO i have a 10 bolt with 3.73's and a stock posi. included is a set of new in the box richmond gears(200 by themselves). The rear has new bearings and races all around and new jegs gears. i dont know if i set it up wrong or if its the gears...
Started by tpibird305spd on
, 18 posts
by 7 people.
Answer Snippets (Read the full thread at thirdgen):
|
