|
In November, I replaced my AC Belt, Engine Belt, Hydraulic Tensioner and Pulley for my 04 3.0 at 85K miles. Here are DIY photos:
TOOLS
IN MY DID, I USED mm SOCKET SIZE, IF YOU DON'T USE mm SOCKET, USE SOCKET TOOLS SUCH
AS 5/8 INCHES ANH 9/16 INCHES SOCKETS...
Started by StartX5 on
, 5 posts
by 2 people.
Answer Snippets (Read the full thread at xoutpost):
A retrofit kit with needed parts for conversion), just wanted to be sure I needed the right parts, i.e..
|
|
Im about to set the final tension on the cam belts.. i know it is to be set at 2.5mm . Im on the right side facing the motor should i put my feeler gauge on the left of the tensioner or on the right of the tensioner where the lip is higher? Im talking...
Started by alfonso on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at ferrarichat):
Im on the right side facing the motor should i put my feeler gauge on the left of the tensioner or on the right of the tensioner....
I know it is to be set at 2.5mm.
|
|
String Tension Meter Does anyone know where I can get a meter to test the string tension of a racket in the uk ?
Thanks
Started by simon224 on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at badmintoncentral):
Accurate, lets say I strung a tennis racquet @ 62lbs, the tension reader will read 59 - 60 lbs right after it does is you record your STI reading right after the stringjob, if the tension reading drop more than 5 for the ....
|
Ask your Facebook Friends
|
Hi, I've been learning f# in the previous days, writing a small project which, at last, works (with the help of SO, of course).
I'm trying to learn to be as idiomatic as possible, which basically means that I try to not mutate my data structures. This...
Started by Francesco on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at stackoverflow):
This is costing me a lot of effort the result I want if node 'D' is asked to steal... .
That's your problem right there.
No you don't.
What do you think about this "tension" which I am experiencing? Am I interpreting the "never mutate of a tree.
|
|
I have seen a lot of posts from people supporting low tensions for their poly strings...i.e. in the 40 pound range. I normally string my poly mains around 60 and when they start to lose tension the strings start moving around.
So, if you start with your...
Started by Jack2010 on
, 13 posts
by 11 people.
Answer Snippets (Read the full thread at tennis-warehouse):
No I think from my experience that polys play better at low tension as snap-back is greater hence more spin at lower tension.
Has something to do with the fact that they arent stretched as much by stringing a higher tension so.
|
|
Anyone make there own spring tensioner .Pictures?
Started by ouh506 on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at clubchopper):
|
|
Ive heard of using a proper tensioned wheel spoke to compare the pitch to use as a starting point but are there any other ways to get the tension close?
The reason is because my new Arch Ex 29" wheelset spokes are very soft. If I grab and pinch two spokes...
Started by Ace5high on
, 19 posts
by 10 people.
Answer Snippets (Read the full thread at mtbr):
At some point Ill get a tension meter but didn't want to do it right now only? use a tension meter Quote....
Does that sound right few rides...
Would to release tension on the "soft side" they flex a good 8-10mm each side.
|
|
Posted 11 February 2012 - 01:27 PM
My timing belt tensioner not movint.Is it rusted?
Started by Tomas44 on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at typeaccord):
Posted Yesterday, 08:25 PM
A mechanic will change.
One puley near alternator.if I buy belt,latter I can't put.Is it right?What belt is better? Posted,that I am right for change this parts and stop sqeez.
|
|
Just got a little box in the mail. here are the insides.
the tensioner itself is made from one solid piece of machined aluminum. it has a tension rod that is threaded into the top of the tensioner body. it twists up and down to get the desired tension...
Started by dontbuyprelude on
, 25 posts
by 17 people.
Answer Snippets (Read the full thread at preludepower):
Make sure its snug but not like have enough tension?....
Rotate twice check again ..
This is a bit off that the belt has a little tension on it ..
Threadlocker on the tension rod's threads right before you tighten the jam nut.
|
|
Does anyone happen to know the standard tension calculation formula for lbs vs web width and film gauge?
We print on poly, but at this time I cannot locate a guide to the exact tension (lbs, once we have converted over on our German press) for our initial...
Started by M. Scott on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at flexoexchange):
For half-mil thick film, it would be half that....
Tension settings always lbs per linear inch, 1.0 mils thickness, and 30" web width, the value for tension is 30 lbs.
We print on Poly and i try to keep it as simple and standard as possible .
|
