|
Alright for a while now ive been thinking of putting hydraulic roller lifters on my solid cam but have heard that some of the ramp rates on solid roller cams are to steep and will destroy the lifters but compared to most roller cams out for big fords ...
Started by 79Bronco429 on
, 14 posts
by 4 people.
Answer Snippets (Read the full thread at 460ford):
Solid roller cam lobes can use hydraulic roller lifters but, most can't.
|
|
I have a fender roller for sale. It was used on one car. This is a general brand roller. Fits 4x100 and 5x114, but not 100% positive for 4x114. I assume it will fit sense it fits 4x100 and 4x114 is just a bigger diameter and the roller has oval holes ...
Started by SiR_K20 on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at k20a):
Great price.
|
|
FS : Used Balanceiga Pen (Roller Ball) For sale :
Brand : Balancaiga
Item : Pen (Roller Ball)
Condition : 7.5/10
Box : Yes
Price : $60
Contact : 96923908
Pm me if u need pic
Started by vince_hiro on
, 5 posts
by 2 people.
Answer Snippets (Read the full thread at sg-roc):
Used Balenciaga.
Special at $50 Special price special bundle price for this week .
Still available.
|
Ask your Facebook Friends
|
WTS_Gently used Delta Table Saw_10" with fence and rollers I have a 10" Delta Table saw, used 1/2 dozen times only for sale. The Model No. is TS300 and it comes with a sturdy frame. I am also including the rollers that I bought for it. Looks and feels...
Started by Choobchi on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at canadianwoodworking):
Re: WTS_Gently used....
Re: WTS_Gently used the shop...
It's hard to tell initially which ones are nuts.
Matt
People are like a box of chocolates.
Re: WTS_Gently used Delta Table Saw_10" with fence and rollers Kid with vacuum extra...
|
|
For sale: Harland Sharp 1.7 roller rockers in very good condition. These are for 7/16 studs. $180.00, plus shipping (ehill54716@yahoo.com)
Started by seneg on
, 9 posts
by 2 people.
Answer Snippets (Read the full thread at corral):
(ehill54716@yahoo.com) TTT TTT TTT TTT pm sent....
TTT TTT price reduced to $160.00 plus shipping.
|
|
I have a nice used (and never had any problems with it) stock 302 H.O roller camshaft and hydraulic roller lifters for 87-93 fox mustang 5L's. $100 for both OBO. Or would separate
cam $50
roller lifters $50
Started by madmancclain on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at corral):
Make offer! bump.
PM sent <bump> Still have both cam and lifters.
Whats your Best deal shipped on the Stock Cam I dont need the lifters .
|
|
What roller lifter would you recommend?
I have a sbc 406 with about a 600 lift cam. What roller lifter would you recommend?
Started by knkracing on
, 11 posts
by 10 people.
Answer Snippets (Read the full thread at yellowbullet):
Lift 595, lobe separation 108 Re: What roller lifter would you recommend?
i have used comp camsRe: What roller lifter would you recommend?
Solid roller? Hydraulic Roller? Drag? Street? What: What roller lifter....
|
|
The only difference between a Roller and non-roller block is the two tapped holes in the lifter valley correct? If they were tapped, then it could accept stock mustang roller lifters?
Started by Diabolic on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at nloc):
But the guy in the post above just stated that he used the spider, dog bones, and stock roller lifters of stock roller lifters.
|
|
Looking at purchasing a used self propelled roller have questions Thinking of upgradig to a self propelled smooth drum roller. Thinking of a 54 inch wide drum. Not sure if need both drum and wheel powered unit what do you think?
Is 54 inch too small for...
Started by lake side bob on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at heavyequipmentforums):
I too need a roller for a road maintenance job I've just received.
To manuver, kinda clucky feeling...
|
|
USED CROWER SOLID ROLLER LIFTERS .PART #66215h-16. THEY HAVE ABOUT 1000 MILES. $325 SHIPPED
Started by 1980cobra on
, 29 posts
by 7 people.
Answer Snippets (Read the full thread at corral):
The part number, but these are for a solid roller correct? yes they are solid roller.
|
