Omgili - forum search, search forums  
  

Discussions about vacuum chuck

Displaying 1 - 10 out of 1,032 discussions.  
RSS Feed Options
Time Frame: (Any time)   Minimum number of replies: (2)   Minimum number of discussing users: (0)
  |  

Page: 1   2   3   4   5   6   7   8   9   10  
Keep this page open to be updated with the newest discussions automatically.
03-27-2011, 5:41 PM #2 James Combs View Profile View Forum Posts View Blog Entries Visit Homepage View Articles Contributor Join Date Dec 2009 Location Mount Sterling, KY Posts 1,676 The Pump These photos show the pump and filter unit. With the connection...
Started by on , 13 posts by 9 people.  
The other photos just blow up a few of them up the chuck being tested then in ....
I found an old piece of coupler and turned and taped shows all the steps I went through to make the chuck.
The Chuck This is the actual chuck.
12-18-2011, 12:05 PM #2 Steve Schlumpf View Profile View Forum Posts View Blog Entries Visit Homepage View Articles Moderator Join Date Oct 2006 Location Harvey, Michigan Posts 16,389 Don - Thanks for sharing! Glad you weren't hurt and that your bowl ...
Started by on , 13 posts by 12 people.  
When everything....
If needed.
I place it on the chuck and apply vacuum and read.
I keed a small aluminum plate handy.
Ok...second...I'm getting a vacuum chuck in February so I'll be sure to make a note to "look at my mentioned.
Vacuum chuck for ct128 i have done a search on this forum for a vacuum chuck for the ct128 and found them to be fairly old has anyone had any success with this. i have contacted JT Turning and they told me they could not help me. i am hoping that someone...
Started by on , 4 posts by 4 people.  
Re: vacuum chuck for ct128 If I remember right..the problem with the 128 is connecting to the out: vacuum chuck for ct128 Adrien, My ct128 has 2 threaded holes on either side of the top pully behind: vacuum chuck....
Ask your Facebook Friends
Is there a way to set this hand-wheel up for vacuum chucking? Thanks Quote: : Young Here is my version of a hand wheel for the models of lathes previously discussed . As anyone knows that has one of these lathes , there is a 5" square steel plate on the...
Started by on , 4 posts by 4 people.  
In the center is to accommodate the tapered part of the bearing housing for my Hold Fast vacuum chucking.
12-09-2011, 5:21 PM #2 Alan Trout View Profile View Forum Posts View Blog Entries Visit Homepage View Articles Contributor Join Date Sep 2006 Location San Antonio Posts 1,364 Quinn, Here is a pic of my system that I just put together. The filter I used...
Started by on , 7 posts by 6 people.  
Quinn.
I can surely go from here when the chuck arives.
That it filters anything coming into the pump, whether it is from the chuck or from the bypass valve.
01-11-2012, 11:40 AM #2 Joe Bradshaw View Profile View Forum Posts View Blog Entries View Articles Contributor Join Date Dec 2008 Location Cary, NC Posts 132 Maybe, if you posted a picture of the problem area, we could help.
Started by on , 8 posts by 5 people.  
Thanks Joe.
THere is a bout a 1/32" gap there that the vacuum is leaking out through.
There is a little gap between the adapter and the body of the chuck.
I can't do that until tonight.
On Fri, 1 May 2009 16:40:39 -0500, "Paul Gilbert" <2pgilbert@sbcglobal.net I just bought a Gast 1022 series pump off of Craig's List. It is mounted on a 20 gal. horizontal tank. I am going to use it for a vacuum chuck. Is there any reason to...
Started by on , 4 posts by 4 people.  
Answer Snippets (Read the full thread at omgili):
Then a short piece of 3/8" brake line, attached the transfer bearing ^^^^^^^^^^^^^^^^^^^^^ It sounds like you are adapting a pump/ pressure tank to vacuum service by reversing the Gast for vacuum.....
chuck" through the headstock.
On Sun, 16 Aug 2009 13:05:03 +0200, Gerard <gerard.zwart@nospamxs4all.nl Looking around for a vacuum-pump I wonder how much cfm large, thin walled bowls need to have sufficient holding power?
Started by on , 14 posts by 5 people.  
Answer Snippets (Read the full thread at omgili):
I've held 14" bowls -0700, "....
Remember, the larger the bowl (and chuck) the less vacuum you need - if you have a 12 inch vac chuck diameter chuck is VERY different than the same vacuum with a 4" or 6" diameter...
I am just curriouse to see what your favorite non-robotic vacuum. my favorite vacuum was the phantom lighting vacuum. I got it in 2003 in a Costco going out of business sale. roomba 510, roomba 440, roomba 550 (parts bot), roomba red (programing robot...
Started by on , 19 posts by 10 people.  
Blinds and crevices as well as a regular vacuum head for carpet and other flooring.
Question ???? should , at idle should there be any vacuum advance at the distributor ? If not why ? If so why? Len 1980 spyder 1980 sunbird hatchback
Started by on , 15 posts by 9 people.  
Answer Snippets (Read the full thread at H-Body):
Chuck I think you got that a littleAt idle....
I guess if you believe what you read the fluctuations of the idle caused by the timing change with the vacuum.
Chuck Wow .
Of the idle caused by the timing change with the vacuum.
Page: 1   2   3   4   5   6   7   8   9   10  

Related Message Boards & Forums

  • Turner's
  • Turning
  • The Official H-Body Internet Community • Carb/Intake/EFI Induction Tech
  • General Chit-Chat (Off Topic) • Robot Reviews
  • WOODTURNING - GENERAL - Woodwork
More Information


Forum Search About Omgili Help Plugins Forum/Board Owners Privacy

i
In Title
In Topic
In Reply
Exclude
Boost