|
Hello all,
At the moment my router is still in the planning stage and will of the moving gantry style, I would appreciate some feedback on my plan to use a vacuum table and any cheap alternatives for a vacuum pump.
Most of the work to be done on the router...
Started by garagefela on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at cnczone):
I also swapped the hoses over to see how much it
would that also .
The pump can extract
air to 90%+ vacuum.
Mike Hi there,
I made a low cost vacuum pump out of a car airconditoner pump, an old 1/3 hp
electric belt.
|
|
Vacuum pump?
I have a sbc 421c.i. 14.1 comp and i was wondering which vacuum pump i need to buy. thanks.
Started by sbcman80 on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at yellowbullet):
Re: vacuum pump?
The GZ Motorsports pumps are nice.
|
|
Min vac for Vacuum pump.
What is the minimum vacuum pull for a wet sump engine? Moroso 3 vane pump. If low pull (5") at rpm can it effect the engine at all ?
Started by Pontiac Dude on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at yellowbullet):
Keep in mind as the crankcase vacuum increases, your piston pin for Vacuum....
I believe vacuum your pump can produce/regulate.
Yes, any negative crankcase pressure should be of benefit.
Re: Min vac for Vacuum pump.
|
Ask your Facebook Friends
|
Yellow Jacket 93600 7 CFM Bullet Vacuum Pump
What the verdict?
Started by JBM1000 on
, 13 posts
by 10 people.
Answer Snippets (Read the full thread at hvac-talk):
Told him my 6 CFM that the boiling....
Quickly educated him about hose size versus pump size.
Told him my 6 CFM pump to make vacuum time shorter.
Quickly educated him about hose size versus pump size.
vacuum time shorter.
|
|
So speak up and let me know what you have done to relocate the vacuum pump on your 'b/2B/3B/2H' diesels.
i am getting rid of the old vacuum pump mounted on the back of the alternator and going with a 100 amp alternator and remote pump.
let me know.
or...
Started by crushers on
, 17 posts
by 11 people.
Answer Snippets (Read the full thread at ih8mud):
Http://www.amazon.com/Dorman-904-214...8807519&sr=1-6
Reviews 28146 Electric ....
As you probably are aware, the 1HDT, 1HZ and 1PZ all had a separate vacuum pump from the alternator electric vacuum pump is by far the cheapest.
Related shopping results:
|
|
Crank case vacuum pump users please chime in...
I decide to start my own thread about my vacuum belt setup after posting in the above thread. I've done alot of research and could never find any good write ups on belt driven vacuum pump setups with real...
Started by 91GTman on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at corral):
Bolts to an ear on the vacuum pump and the top end goes on the end of the lower alternator boltMy goal is to get 10" of vaccum on the crank case in the higher RPMs and a positive vacuum at all setups because of low vacuum ....
|
|
I want to start playing with some vacuum bagging and have been looking at vacuum pumps.
For now I just want to try vacuum bagging a dozen or so square feet, I am not trying to vacuum bag a 20' foot hull all at once.
I have been looking at single stage...
Started by chrisk on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at woodenboat):
I can regulate the vacuum level of the pump as a high vacuum pump that takes a long while to empty the bag leaves less time before once you have finished....
And a valve that bleeds air in in the suction side of the pump.
|
|
Hey guys my vacuum pump is not working
do i just need to replace the Diaphram?
where can i get a rebuilt kit?
thanks
Started by malone on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at vwdiesel):
Then repair the pump later.....
Next time I find I am brakeless the fix will take but 5 mins .
Hey guys my vacuum pump is not working
do i just need to replace the Diaphram?
where can i get a spare pump and the kit to go in it.
|
|
Lets see your Vacuum Pump setups
I was thinking about going with one.
I am running a BBC with an alternator. I was wondering what mandrel and pulleys I would need to get it all running and keeping all the belts inline.
Moroso has a slick mount available...
Started by a468bu on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at yellowbullet):
Re: Lets see your Vacuum Pump setups
Here is the jones racing products vacuum pump and alternator/albums/e1...n_DSCN2464.jpg Re: Lets see your Vacuum Pump setups
I guess I should have mentioned for the link ....
|
|
Recently picked up a pump for the car but I am trying to figure out where I am supposed to put a gauge to set up the amount of vacuum i want to pull. I'm looking for around 11-12". Just not sure where i can hook a gauge to? Any help is appreciated.
Started by subhumanzz on
, 19 posts
by 8 people.
Answer Snippets (Read the full thread at ls1tech):
If you can get it ....
The vacuum will be set by the bypass valve, and the ratio of the pump for sure.
Since you that ran to the vac.
The vacuum will be set by the bypass valve, and the ratio of the pump pulley's.
|
