|
OK, I have a 16' deep x 14' wide room, wood construction, and the seating position is slightly behind the middle of the room. Speakers are ML Dynamo 700 (downfiring, and somewhat close to the front corner, but perhaps not close enough) and Monitor Audio...
Started by Silmott on
, 27 posts
by 13 people.
Answer Snippets (Read the full thread at avsforum):
Move your seat....
Thank you, I guess is a natural bass null.
I have the same problem, I hope there are some suggestions, moving the seating position isn't an option for me.
Move your seat back.
The center of the room is a natural bass null .
|
|
Seating 7 I need some help. I'm looking for a new vehicle that can seat seven, but I'm on a budget (25Kish). So far, I've been done a lot of research, and I've found 4-5 options in that price range: Kia Sorento, Kia Sedona, Dodge Journey, Dodge Caravan...
Started by erikthered on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at thebreakaway):
I did a few in the back seat....
How's the back seat? I may look into it after all.
That meant I didn't think it would be big enough .
It was as if they had taken the seat cushion and set it on the floor.
There was no vertical room.
|
|
Hi guys,
Ive had this TV for about a year now - all of a sudden thin vertical lines have covered my screen (show in link below) No matter what input I choose.
These lines no not move about - and are multi-coloured. Again, they litteraly fill my screen...
Started by adyehh on
, 19 posts
by 16 people.
Answer Snippets (Read the full thread at avsforum):
If you a get full screen of thin vertical multi a get full screen of thin vertical....
|
Ask your Facebook Friends
|
Posted 20 May 2012 - 11:06 AM
So, after finishins some jobs I now have enough money to fix my forge and decided to make a new one.
The basic design is two coats of kaowool topped with satanite using a blower setup, but I remain undecided in regards of...
Started by Santiago Perez on
, 16 posts
by 4 people.
Answer Snippets (Read the full thread at dfoggknives):
I am forging a 22" Naginata....
2) It's true (more or less) that it's difficult to HT in a vertical blade.
Posted 20 May 2012 - 11:58 AM
1) I don't believe that horizontal or vertical makes any difference that will melt steel is no big deal.
|
|
I have already searched and know how to get to the vertical adjusters but don't know which way to turn them. (Using the bottom two holes to access the T20 torx adjuster)
I turned it a couple times counter clockwise and did not see any change. I don't ...
Started by sickf4i on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at m3forum):
|
|
Hello guys,
I recently bought a new plasma tv, the panasonic 42st50, this is my first plasma tv and I must say that I am impressed. It looks so much better than my old lcd, I do have one question though:
Viewing angles are supposed to be an advantage ...
Started by idemedosumom on
, 10 posts
by 7 people.
Answer Snippets (Read the full thread at avsforum):
The only way to get around with the filter, even though as you ... .
It doesn't affect the horizontal viewing angle though, only vertical, so you notice it when you stand up.
Noticed, the vertical viewing angle is crap for these plasmas now.
|
|
I can say that I wasn't warned - looks like I've been DPx'd: Vertical Blade Play
I was duly warned by several folks on this forum but based on the size, shape and specification of the DPx 2.0 I went ahead and ordered one.
I got it in March and it has...
Started by Peroni1973 on
, 20 posts
by 9 people.
Answer Snippets (Read the full thread at bladeforums):
I feel yer pain.
And i'm not 'blaming' you or anyone for this situation .
Past the seating in point.
|
|
On Thu, 27 Aug 2009 19:57:05 GMT, "The Medway Handyman" <davidlang@nospamblueyonder.co.uk
I've been asked to build some bench seating. I'm sure there are standard
dimensions for seat heights, widths, depths etc. Anyone know of a source?
Measured...
Started by The Medway Handyman on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at omgili):
Seat height should not exceed-adjustable chair should not exceed....
Quite a large kirk that would seat some 500, and built if this is for sitting up (at a table) or sitting back
(relaxing).
All the pews and replace with movable seating.
|
|
OK, I was planning to make a 'RoyRector' style video of this, but never could find the time to film and edit it. There been a lot of questions on this forum about the authenticity of the seat offered by Northern. Some claim it's a 'knockoff'. Well it'...
Started by MowerDude on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at mytractorforum):
~$250 more for yellow tinted with a seat similar to that one, only fabric instead of vinyl! Great review and Thankyou! I like the black too, crawl into any big....
Hey, it's your money.
Never saw a lift truck with a coloured seat.
Commercial.
|
|
I am finishing my seating panels so I can move the build to the upholsterer. I am looking for advice on attaching the seats. The panels look like this:
Attachment:
IMG_0863.JPG [ 540.86 KiB | Viewed 224 times ]
I am using gravity to hold things in place...
Started by Bruce Dow on
, 10 posts
by 8 people.
Answer Snippets (Read the full thread at glen-l):
There....
They hook under the deck frame right behind the seat, and then the bottom of the seat back swings down and stays in place against a stop block by friction.
Bill I bent some brackets that are screwed to the seat back.
Velcro.
|
