|
Hi all
2005 cbr.
When I sit on the bike and look down past the handlebar, at the rear of the headlight assembly , i.e below and to the side of the instrument cluster, just in front of the forks, I can see a set of ugly looking wires protruding from the...
Started by clx on
, 9 posts
by 4 people.
Answer Snippets (Read the full thread at 600rr):
That was the case look like....
That was the case then there is a good chance the prev owner did not really do a good job with the wire placement.
Then there is a good chance the prev owner did not really do a good job with the wire placement.
|
|
Just reading up on spring, and when using DI in spring, if you set the bean to be a singleton (default), then a single instance of the class will be 'dispensed', while prototype forces a new instance each time.
What are the ramifications of having the...
Started by mrblah on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
Any changes in that object will be visible (via behaviour or otherwise) to all.
To the same object.
|
|
I'm trying to get my horn working again after installing an NRG Quick Release. A year or so back I swapped out the stock steering wheel for an ItalVolanti from TeamDI. The wheel works fine for me and the horn worked fine when I installed it.
Now, after...
Started by VaTechE36 on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at bimmerforums):
Or you did what the guy I bought the adapter from and just let the wire wrap around the column to carry to solder a wire to the "ground" on the horn button to connect to the wire passing through the NRG hub is failing me right now....
|
Ask your Facebook Friends
|
CX-9 Hidden Hitch Install with Mazda OEM wiring harness (pictures) Installed a Hidden Hitch Class III and the Mazda OEM wiring harness on my 2009 CX-9 GT AWD today. I figured I would post pics to share.
Mazda OEM hitch harness part number is: 0000-8E-...
Started by gtxjoe on
, 15 posts
by 12 people.
Answer Snippets (Read the full thread at mazdas247):
Regarding the wiring install on a trailer hitch: Do I need to run a wire to the battery or just plugDoes the receiver have a bracket for the wiring connector, or does it dangle?
Nice to finally see 6AT Just install my wire....
|
|
Im looking for a little side work. Ive been working on vehicle electronics for 5 years...2 way radio installation, lighting for emergency vehicles, sirens, custom console work. Anyone needing help with wiring...troubleshooting or installation? Give me...
Started by sunk on
, 20 posts
by 7 people.
Answer Snippets (Read the full thread at frontrange4x4):
Let me know discussions with some other....
You need to be good at reading wiring schematics upside down...
Probably 8 wires.
ECU is a to get to, directions are pretty clear .
For wiring in a piggy back Split Second ECU on my 3.4L Yota.
|
|
A few people have asked about chaning over a Roscoe with the Bart preamp to a Glockenklang preamp. First, the Bartolini is wired for 18 volts and the Glock is wired for 9 volts. You can still use both batteries with the Glock, but you will have to rewire...
Started by CrashClint on
, 18 posts
by 6 people.
Answer Snippets (Read the full thread at talkbass):
With that wire....
I managed to isolate it- by desoldering the cavity ground wire from the preamp module ground wire connects.
I know with the Audere, they wire theirs, as suspected.
Leads and shielding do not go to cavity ground.
|
|
My '90 RS 305 TBI is throwing a code 42, and it's a bit hard to start and idles a little rough. Other than that it runs fine.
I've been trying to determine the cause of the code, which states it's either an open or short in the EST circuit, a faulty ignition...
Started by kkingsrulee on
, 14 posts
by 3 people.
Answer Snippets (Read the full thread at thirdgen):
Then you wont have....
Or you can cheat and cut the wire a few inches from each end and solder/splice your own.
If you do find a short/open then yes you will have to follow that wire through the harness and find the break.
The ECU would see.
|
|
1 guage wiring, fuse holders, fuses, etc 1. Products: Wiring etc.
3 ANL Fuse Holders (no covers)
2 300 Amp ANL Fuses
1 gauge welding cable
Red Pieces
14 ft
34'' ring terminals on both ends
3 18'' pieces with ring terminals on both ends
15'' 2 ring terminals...
Started by cman06 on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at caraudio):
Batteries in parallel, which will be visible, so I want clean wire, ya know?
also, any size comparison for wire to run a buncha batteries in parallel, which will be visible, so I want clean wire, ya knowRe: 1 guage ....
|
|
Building a new home (yay me for supporting the economy) that is now framed, roof on, and putting in the furnace to dry it out so we can go to town on the interior. We have a contractor with a base package of stuff that we can then upgrade.
The wiring ...
Started by China Guy on
, 43 posts
by 23 people.
Answer Snippets (Read the full thread at straightdope):
We had all of our Cat 5 wiring pulled to the far side of our unfinished problem locations with....
These should all be on their own circuit breaker and wired with 3 wire power cable a 'control center' on the main floor.
wiring.
|
|
Ok guys i have been looking through the forums and i have noticed people saying i wish i had a portable Xbox but i am not daring to tamper with wires. Well now you do not have to. No more stress.
Ok first off i am going to start by giving you an insight...
Started by XBOXMODDERINNEED on
, 11 posts
by 3 people.
Answer Snippets (Read the full thread at xbox-scene):
Cheers Guys Ok just a real quick update.
Roll for it on order so no screws will be visible.
|
