|
New ARP wheel studs, full set for 1 car.
# ARP 100-7708 & # ARP 100-7717, pair of each.
$110 shipped
Started by teamscss.com on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at ls1gto):
I am looking for some new ARP wheel studs.
|
|
Wheel studs Is there another Nissan model or any other car for that matter that has a longer stud than a stock s13 but will still fit into the stock hub. I have to run an 8mm slip on spacer for my wheels but need longer studs, don't really want to fork...
Started by Bullitt_S13 on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at tamparacing):
-Royce cheap ARP 100-7708 ARP Wheel Studs 1972 nova ss
89 240 sr20det
2002why do you need bigger studs for 8mm spacer -Steez- Because I'm not happy with the number of threads I'm getting on the stock studs....
Good luck to you.
Pitch.
|
|
John Fowler, my wheel and tire expert at Consumers Tires in Markham Ontario. asked me post this question. I went to see him this morning to have a new set of winter tires installed on my OEM rims. I only have about 1700 kms on the car and this was the...
Started by elro on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at 166):
All of my T2 Transporters (Bus, whatever you like to call it) had wheel studs.
Of sliding a wheel onto a stud-mounted hub usually involves scraping the wheel over the top of the threads change.
|
Ask your Facebook Friends
|
I tried locating some longer wheel studs for the front of my bronco at napa and they came up short.
Anyone have better luck?
I only need the studs to be a 1/4 to 1/2 inch longer. Id like to put my 1/4 wheel spacers back on and make my turning radius a...
Started by myklstrng on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at classicbroncos):
Can chuck them up be much easier ....
My be much easier (and cheaper) to buy the longer wheel studs and have them cut to length.
They are about $60 for a set of 5.
My brother just bought a set of 3.5" wheel studs from summit.
|
|
Would anyone know where I can get longer wheel studs for the front of my 06 chrysler 300c? I have done the brembo brake conversion and am having to run spacers. I would like longer studs for piece of mind..
Started by bozo4 on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at lxforums):
I have been running them.
Black studs that are 3/4 longer and fit the bill quite well.
The Dorman 509's.
|
|
Longer than factory wheel studs and wheel spacers, why is this bad? Is there a problem with the studs snapping or what?
Started by DaGuse5853Z on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at s10forum):
wheels studs....
Id personally have longer wheel studs then it really doesnt matter as all the weight is on the hub and the studs just keep the wheel aginst it...
Ran it with no problems.
The weight was resting on that.
|
|
Is there another Nissan model or any other car for that matter that has a longer stud than a stock s13 but will still fit into the stock hub. I have to run an 8mm slip on spacer for my wheels but need longer studs, don't really want to fork out the dough...
Started by Bullitt_S13 on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at tamparacing):
When I first ran these particular wheels and spacers on stock studs....
100-7708 ARP Wheel Studswhy do you need bigger studs for 8mm spacer Because I'm not happy with the number of threads I'm getting on the stock studs.
|
|
Extended wheel studs hi guys
i bought some extended wheel studs off egay and the do not fit as they are 29 spline and the ones on the car are 35 spline now my question is where will i get the correct ones from?
rep waiting Quote: jay: Some say a thousand...
Started by madman on
, 19 posts
by 7 people.
Answer Snippets (Read the full thread at toyotagtturbo):
John, I can't find any were measuring wheel studs by spline count.
Wheel Studs:
DP DF L PART# Price Each
12 M12X1.5 70mm CRP/3 3.50
12 M12X1.25 70mm CRP/7 3.50
13 going forcing them in...
|
|
Can anyone help translate, what is the shoulder, knurl, and head marks? Do you think the Napa part number i got is a good replacement for longer studs? I'm running a 10mm spacer.
Neon Front stud:
Wheel Bolt Head Marks : 285
Wheel Bolt Knurl Dia. : 14....
Started by jdt18 on
, 29 posts
by 11 people.
Answer Snippets (Read the full thread at neons):
For stock studs98 Ford Taurus napa part....
L3: The length of the nose.
L2: The thickness of the stud head.
: : Wheel Bolt Thread Size : M12-1.5 I was at the junkyard today so I popped some 96-99 Taurus studs out of the usable threads.
|
|
Do the axle shafts have to be removed in order to change wheel studs on naa,600,800 tractors or is there a "short cut" that someone out there might have?? (plasma and cutting torches) are not considered short cuts in some cases..
Thanks for any info you...
Started by TSJ on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at yesterdaystractors):
Replaceing rear wheel studs sounds like he doesn't want to cut has removeable hubs like ....
Here is a link to a post someone else made with pictures showing how he did it .
To replace the wheel studs without removing the axle.
|
