|
Hi folks,
I've got a lava tube and I've just bought a couple of these Vision Egos here:
http://www.liberty-f...oryid=16&id=165
It says on the site
Quote: The indulgence and Lavatube VV will need a 510 to eGo adapter though due to the skirting on the Vision...
Started by OFJ on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at ukvapers):
Some of those adapters can be a bit, on 21 May 2012 - 02:5....
Only have through the Ego adapter? If OK, that proves the adapter is fine.
Vaping a carto as we speak.
Back to top Lava tube is fine.
It was nice while it lasted.
|
|
4.6 EGR tube to Manifold adapter
Need the adapter that threads into the 4.6 exhaust manifold that the EGR pipe attaches to.
Looks like this.
Started by theterminator93 on
, 2 posts
by 1 people.
Answer Snippets (Read the full thread at tccoa):
Jason @ Ford Parts Counter came through with this one! :) .
|
|
Lumix DMC-LX3 with film can flash diffuser and adapter tube
Started by Karel Julien Cole on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at pinterest):
|
Ask your Facebook Friends
|
I am looking for a adapter for the back of a CAE In/out box that the torque tube adapts to. I have one on the box that I have but it does not have the same bolt pattern that my torque tube clamps have and the torque tube does not fit in the adapter. The...
Started by Mattbee on
, 2 posts
by 1 people.
Answer Snippets (Read the full thread at jalopyjournal):
|
|
WTS Tamron 90/2.5 macro adaptall mount + 1:1 extension tube + adapter.
3 adapter for selection: minolta / contax yashica / nikon
this ia a manual lens, in great condition
glass is clean and free from fungus / haze / scratches
focus smooth, aperture snappy...
Started by pfsam on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at photomalaysia):
|
|
Obviously these pieces combined give you a complete folding stock replacement for the standard stock on a 556, which is what my plan was. But after finally assembling it all, I just didnt like the feel as much as the Swiss folder, and I have decided to...
Started by dwd1985 on
, 5 posts
by 2 people.
Answer Snippets (Read the full thread at sigforum):
It can be found.
|
|
Easily Mount Fanatec Shifter Adapter to 80/20 Tubing If you have already have a rig made of 80/20 aluminum extrusion or would like to add a shifter mount made of 80/20 extrusion to your rig using the Fanatec shift adapter, it is quite easy.
The Fanatec...
Started by JogoASobi on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at nogripracing):
|
|
There was some discussion in another thread (here: Which Genz Head would sound close to the Little Mark Tube800? ) about the effect of the "Tube" preamp channel of the LMT800 head. I decided that I wanted to figure out for myself exactly what the difference...
Started by onosson on
, 12 posts
by 3 people.
Answer Snippets (Read the full thread at talkbass):
But notice that little bump around 250-300Hz on the....
There is a bit more energy below 100Hz on the tube preamp, not too much difference between 100-200Hz.
Solid state is on the left again, tube on the right.
The frequency as I mentioned).
|
|
In a couple of areas we have multiple devices that all run on 5v and have multiple adapters with standard jacks, which annoyingly require multiple sockets and cables.
Does anything like an adapter splitter exist? Or an adapter with multiple leads?
Cheers...
Started by Andrew Grant on
, 6 posts
by 6 people.
Answer Snippets (Read the full thread at serverfault):
Tape or shrink-tube.
Then solder together some cords in parallel that wire into the base .
|
|
FS: EzFocus Adapters! Focusing Adapter For Kryton's and Others! Also see here! (for AixiZ 445 custom focus adapters)
http://laserpointerforums.com/f64/fs-445-custom-focus-knob-ezfocus-adapter-aixiz-glass-lenses-51727.html
This is a great little EzFocus...
Started by jayrob on
, 24 posts
by 11 people.
Answer Snippets (Read the full thread at laserpointerforums):
8-)
I don't know if he ....
I messaged him about my EzFocus adapter.
Re: FS: Kryton Focus Adapter! Easy Focus For Kryto don't you make the kryton's???? Re: FS: Kryton Focus Adapter! Easy Focus For Kryto The Kryton is Kenom's design...
|
