|
K so my amp is only doing mono apparently. Any ideas what to look for? i recapped the unit recently. Have no idea if this has been going on for a longer time, only just noticed it when playing some tracks where you would notice.
Started by dread_lion on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at audiokarma):
Have you tried flipping it between the two positions to see if you get stereo or is it just mono on....
The toggle switch seems to do nothing between stereo and mono.
So i can only assume the amp is playing everything in mono.
|
|
Hello,
I was just wondering if all line inputs were mono for audio interfaces. I have an M Audio fast track, and I was attempting to record a DJ mix out of the stereo output of the mixer (RCA L/R into a 1/8" plug with a 1/4" adapter) and into the 1/4"...
Started by Robomb on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at gearslutz):
TS connections, on the other hand, are always unbalanced mono....
Enough to say, yes they are mono, left and right, input 1 &2 you just need 2x RCA to 1/4' cables and all an unbalanced stereo signal, or a balanced mono signal.
|
|
So with the encouragement from AK'ers on the D&S forum I imported a pair of mono blocks from Canada
No tubes so on the shopping list are
4 12au7
4 5881
2 5v4g
I will need lots of information, pointers, suggestions, advice, warnings, direction ect. The...
Started by b brian on
, 13 posts
by 4 people.
Answer Snippets (Read the full thread at audiokarma):
Looks like a 5 or 8 ....
Just to the task.
The HK Deuce had this problem with some grounds under the speaker strip screws .
And close to the DC balance they connect.
With them!
Dave So per the plans V-2 is closest to the speaker connection.
|
Ask your Facebook Friends
|
Stereo guitar cable vs mono Hi
http://www.amazon.com/Planet-Waves-C.../dp/B0009EY116
Can I use this for my guitar (strat)? Will there be any difference?
Thanks
Jon
Started by jomaco on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at harmony-central):
Originally into a guitar box that uses a....
This guitar,
has piezo pickups in the bridge to an accoustic amp, and the electric guitar pickup signal no a normal electric guitar amp.
Stereo would be silly.
Most guitars use mono cables.
Related shopping results:
|
|
I found this amp recently sitting on the side of the road and i need some help on how to go about using it should i run it mono like it is or take it apart and use some of the parts for a stereo amp project which i would rather have it has been really...
Started by kirkendoll on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at audiokarma):
WOW thats a find,....
I'm not really up on console bits, but I would bet that you could sell the amp chassis and those tubes for enough buy a nice stereo amp.
You found a Capeheart amp stuffed with 2A3s on the side of the road?!? Wow.
|
|
I have an 01 530i with DSP. i am planning on installing a mono sub amp tomorrow, but after reading through tons of archives i am still confused about the best way to get the signal.
from what i understand, i can get an amplified sub signal from the harness...
Started by gixer6 on
, 18 posts
by 12 people.
Answer Snippets (Read the full thread at bimmerforums):
Either way is OK to use and you will not notice a difference in sound low level output into your new amp.
connect it after the amp.
|
|
Ok so I ended up going with a Pioneer AVH-P8400BH instead of the Pioneer AppRadio 2 . I wanted a "mech-less" head unit since I don't own any CDs and have few DVDs.
I ended up with the P8400BH because it has A2DP and AVRCP bluetooth profiles and auxiliary...
Started by Synomenon on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at anandtech):
Under the front I did post in ....
I have a small class-D mono amp.
RCA outs from your HU into the RCAs on the amp, then connect your wiring harness adapter of the front seats? That's my go-to spot for installing amps.
|
|
2 amps, one cab? I picked up a 5e3 clone off of ebay a couple weeks back. The thing is wired for an 8 ohm load, but the cabinet I have is a 2x12 with 8 ohm speakers, so I would have been running a 4 ohm load, which I knew had the potential to damage the...
Started by ItchyFingers on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at harmony-central):
B) have them wired each goes from mono to stereo, the 2 holes on the stereo side is for each speaker while the hole on the mono side is for both so you can get ....
Speakers with power rating less than the amp will blow the speakers.
|
|
HI GUYS, i HAVE A Yammie Stereo Amp which is about 20 years old. Its been relegated to my shed along with a couple of JAMO 8 ohm speakers. The speakers a re very good and in excellent nick. However, every now and then one of them dies. I wasn't sure whether...
Started by Shedhand on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at woodworkforums):
If it's a dickie wire connection on an input pin then hook your CD player/tuner/whatever to another input on the back of the....
If you don't switch sources then you can just bypass the selector to the volume pot .
connection may do the trick.
|
|
If there is a volume control on these players, could they be used as a pre-amp for a power-amp?
Started by b brian on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at audiokarma):
They sound....
Using the headphone out will have more distortion and I would be more likely to turn you can feed them into a power amp.
You can but it would be better to go out the dock connection and use a passive volume control/pre-amp.
|
