|
Is there any difference between durability analysis and stress analysis? If so what is the difference?
Answer Snippets (Read the full thread at eng-tips):
Stress analysis = prediction of strength, stiffness, buckling, etc under static loads.
|
|
Dear Friends,
The following is the link of excellant pipe stress analysis manual
<![CDATA[[Only Registered And Activated Users Can See Links]
Caution: Download it as soon as possible, the link may dead if it is found to be copywrite material
Started by Paldex on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at egpet):
[This link Point to another.
[This link thanks alot mr abdel halim Additional pipe stress analysis books:
5.
Regarding pipeline ...then do share with me thanks Piping Stress Analysis handbooks:
1.
|
|
Needed Pipe stress analysis book, and Bently AutoPipe software
please help me.
Thank you very much
VINCENT
Started by vuong on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at egpet):
Well Autopipe is available from Bentley and Pipe Stress Analysis books are available.
|
Ask your Facebook Friends
|
Who have the code: IGE/TD/12 PIPEWORK STRESS ANALYSIS FOR GAS INDUSTRY PLANT?
Started by wjw_1980 on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at egpet):
Please share, thanks.
|
|
Hi all,
I have to carry out a stress analysis for a cryogenic network made of flexible vacuum insulated pipes.
The structural integrity under thermal and seismic loading has to be checked. Normally these kind of analysis are performed following a piping...
Answer Snippets (Read the full thread at eng-tips):
What would you be doing, if you knew that you could not fail? .
Apparently there will be no code compliance check, but you will have the stresses.
Then propose to do the analysis and submit your results.
|
|
Hi everyone,
Ive been doing a college project on the stress analysis in a cylinder. I tested the actual cylinder by pressurising it till it failed at 610 bar. i then drew it in inventor and applied the internal pressure. The problem is in anaysising the...
Started by Hughbyrne on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at mcadforums):
|
|
Hi all,
I have to carry out a stress analysis for a cryogenic network made of flexible vacuum insulated pipes.
The structural integrity under thermal and seismic loading has to be checked. Normally these kind of analysis are performed following a piping...
, 1 posts
Answer Snippets (Read the full thread at eng-tips):
|
|
Hello All,
I am a rookie to FEA world. I am using ANSYS14 to perform stress calcualtion on a steel structure. This is static analysis.
I have a 3" thick 50 grade steel plate solidly welded to the tubular structure behind. It takes a concentrated load ...
Answer Snippets (Read the full thread at eng-tips):
Have you done some) ?
if you are truly applying a moment to the... .
Is the high stress near the load ?
the mesh may and increase the number of nodes taking the load and that will increase local stress.
A couple of bolts) or not (eg, a weld).
|
|
Posted 25 December 2010 - 08:22 AM
I have to do a load simulation for a steel structure frame, and I am using a software called Autodesk Inventor. The strange problem is that Im having a hard time to understand the analysis result. The simulation bend...
Started by AjaxChat who on
, 5 posts
by 1 people.
Answer Snippets (Read the full thread at objectivismonline):
The maximum stress was 1.2Mpa something, and in contrast to the 200Mpa yield strength, there should.
|
|
New research showing that almost half of 13,000 patients with head and neck cancers had other health-related problems at the same time is one of the presentations in a special session at the 31st conference of the European Society for Radiotherapy and...
Started by News on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at her2support):
|
