|
I guess I'm in the market for some new axles. I have a friend that is telling me to go with Turner axles or gorilla axles. I would. Go with gorilla axles but have been told that they are hard to get because they seem to always be on back order. Any info...
Started by cbull on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at prcforum):
To spend a stupid, rediculus amount of money on gorilla axles, where is the cheapest place to buy.
|
|
My 27 mm axles are shot on my '97 M3. I looked on realoem and they list the two sizes of axles and from what I could see the diff flange is the same for both and the wheel bearing is the same for both. Are the 27 mm and 38 mm axles interchangeable on ...
Started by chikinhed on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at bimmerforums):
Both axles are for the same application one being solid (27) and the other being hollow shaft (38.
|
|
I just finally got a AWD trans into my car. I have absolutely no axles for it, but I am aware of the Intermediate shaft for the AWD cars. My question is are the 1g and 2g AWD axles/intermediate shafts the same?
Started by teddygram on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at dsmtuners):
My question is are the 1g and 2g AWD axles.
I have absolutely no axles for it, but I am aware of the Intermediate shaft for the AWD cars.
|
Ask your Facebook Friends
|
Looking to upgrade my 08 SRT diff - staying with stock ratio. I need axles and diff so if you have an RT 6speed Ill take those stock axles or SRT9-10 diff and axles. If you have these taking up space - let me know what you have, I am ready to buy today...
Started by fastfranky on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at challengertalk):
Swapped axles as part to the 09+SRT setup, used....
Swapped axles as part by dodgetime have a set of OEM rear axles (half shafts) off of my 2010 SRT8 6 speed.
Have a set of OEM rear axles (half shafts) off of my 2010 SRT8 6 speed.
|
|
GTS Axle Housing. (no diff/axles/brakes)
$100
Zenki non LSD axles $200
Los Angeles area.
Taka.<br /><br />
Modified by Taka at 6:03 PM 10/19/2011 <br /><br />
Modified by Taka at 12:57 AM 11/7/2011 <br /><br />
Modified...
Started by Taka on
, 16 posts
by 10 people.
Answer Snippets (Read the full thread at club4ag):
Interested in the axles...let me know if they....
I can go $160 for the pair.
Others are OK.
Pm'd you Hey bro i'm interested in the axles, but how are the bearings on the axles? The best bearing axles were sold.
Thanks replied.
|
|
Axles and shafts what are the best axles and drive shafts you can buy for emaxx 3908
Started by S10 on
, 19 posts
by 8 people.
Answer Snippets (Read the full thread at traxxas):
I have the traxxas ones but they dont last ive had of steel round stock Im running 4s and ive had two axles pins break and one cup wear out and the pin only Last edited by S10; Yesterday at 1....
I use losi cvds for the axles.
Drive shafts.
|
|
I have heard that some people have had trouble with the Gorilla axles. I want to buy complete rear axles for my XP, where and what do y'all suggest???
Started by xtremetoyzracing on
, 13 posts
by 10 people.
Answer Snippets (Read the full thread at rzrforums):
If I was going to do it all over I would... .
The only problem I had with them is that the "coating" they used on them flaked off immediately, and by that I mean that I hadnt even ridden on the new axles yet.
I have lonestar axles on the rear.
|
|
What are good axles to buy?? i keep braking my axles left and right..mind you my car is stock i do not launch or or do burnouts??
Started by hector2nice on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at srtforums):
Over 100 1....
Lowering springs...the shocks are still good and i just need to check the bushings thanks oem axles are always the best to buy....but as for you breaking axles like that are u letting it wheel hop miles on stock axles.
|
|
Tags : None
I have sway a way axles for my baja now with T1 cv , I see that t2/t4 also have 33 splines just like t1 , will my axles work with t2 cvs??
Alex -San Diego
Well let me just Quote: the late-great Colonel Sanders, who said..."I'm too drunk to...
Started by San Diego Baja.inlandbajas on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at yuku):
But T1 axles have a shoulder which stops the CV from passing through....
The axle diameter and spline are the same.
The axles and CVs were gone so I really didn't think about are thicker than Type 1.
In the junk yard not too long ago.
|
|
Im looking to possibly get new axles and stronger axles all the way around my rhino. But before i do so, i would like to know if there is anyone running the "rhino" brand axles??? Have you had any issues with them???
Started by MUDSLUT23 on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at rhinoforums):
Nick I have a 4 stock axles ill sell ya for $70 shipped.
Brand but I picked up my HD shafts from egay .
|
