|
I pulled these out of my magazine that I have been carrying for some time now. I just noticed this. The one on the right is obviously over crimped and the one on the left is a normal crimp for comparison (same lot, same box). I am a little disappointed...
Started by gunsup on
, 24 posts
by 13 people.
Answer Snippets (Read the full thread at glocktalk):
Bonded) over run was in stores i had whole boxes like that Quote high cost of paying some one a livable wage... .
Needless to say, it was ugly and became range ammo that! Back when the pdx (180gr.
Years and put back in to the boxes and resold.
|
|
I recently bought a Bar Sto extended barrel for my Glock 21. When I first try to install it I found out it needed a bit of filling on the hood to lock up correctly. I did that and it lock up just right. Then I loaded it with a few dummy rounds and when...
Started by bigguy1305 on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at calguns):
Check the distance and position between does not rise to lift the....
Check the distance and position between the bottom of the feed ramp normally then put a empty magazine in and lock the slide back.
In and lock the slide back.
|
|
I just cannot believe this just happened to me and how rude this company was. I am extremely disappointed and feel I was used as free employee for their research.
I received the 1st interview request 2 months ago for a position I really want and did the...
Answer Snippets (Read the full thread at indeed):
People in sales positions are used probably fail the test... .
You probably did a great job, but you did not sell them.
So I came back at 4pm, and at last I was able to meet the HR and demanding.
back because I badly needed a job.
|
Ask your Facebook Friends
|
Hi guys!
So today i tried doing a cover of Round And Round By Ratt, everything recorded in one shot exept the 2nd guitar. I only new the first part of the solo so i improvized the rest including the melodic part after.
What do you think?
Got the backing...
Started by Kippan on
, 18 posts
by 16 people.
Answer Snippets (Read the full thread at kramerforum):
Rock on dude sounds great.your tone is spot on on the rythems awesome live feel to it....great job man Great job here, sound is good and timing right on the spot and tightass Real nice work dude believe Stephen Pearcy would be a really hard....
|
|
By ( benwhite@politico.com ; Twitter: @morningmoneyben )
WELCOME TO JOBS WEEK: BACK NEAR 200K? - Friday’s first quarter GDP number came in weak at 2.2 percent and Mitt Romney and other Republicans pounced on it as evidence of a failing “Obama economy....
Started by TeamPOLITICO on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at politico):
|
|
Hi all,
I'll get straight to the point, I am an addict, of not only opiates but another white devil which will remain anonymous. As many of you know roughly a couple months ago I was posting here working on a tapering schedule which remained on par, I...
Started by Haypress on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at drugs):
|
|
I'm considering the best way to cast a hunting bullet for 10mm. I can get the same mold with or without a gas check base. Now, if I go without a gas check I have to use a harder alloy, but if I use a gas check can I get away with pure, dead-soft lead ...
Started by Oreo on
, 20 posts
by 13 people.
Answer Snippets (Read the full thread at gunloads):
And don't think the ....
Larry Gibson i'd go with the gas check in the 10 mm also similar to larry's.
I push choice in rifles for hunting big game.
I use soft alloyed cast bullets with GCs for hunting with my .357, .41 and 44 Magnums .
back.
|
|
We have a set of shared, static content that we serve up between our websites at http://sstatic.net . Unfortunately, this content is not currently load balanced at all -- it's served from a single server. If that server has problems, all the sites that...
Started by Jeff Atwood on
, 17 posts
by 17 people.
Answer Snippets (Read the full thread at serverfault):
There are a number of valid criticisms of round-robin DNS as load "balancing that.)
If one of your two round....
When one server goes down, the DNS servers have this, at least temporarily .
round robin using DNS to each server's IP address.
|
|
Does anyone have handy the snippets of code to convert an IEEE 754 double to the immediately inferior (resp. superior) float , without changing or assuming anything about the FPU's current rounding mode ?
Note: this constraint probably implies not using...
Started by Pascal Cuoq on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
%a is C99 */ printf("Double: %.20f or greater than the double value... .
To do this job more accurately than just re-combine mantissa and exponent bit's check this out; /* Now, convert that back to double */ tmp = f; /* Print the numbers.
|
|
Rounding off the 2009 G.I. Joe Q&A’s is the January 2010 Round 6 Answers (yeah, I know 2010), and they ready for your viewing. This is the last Q&A before Toy Fair 2010 which is next month. So what little bits of information will we be able to pull out...
Started by WildWeasel on
, 8 posts
by 6 people.
Answer Snippets (Read the full thread at theterrordrome):
If ....
Can you comment on this potential change?
As we move Sightings
Bill: Based on the last round of Q&A's, the Pursuit of Cobra theme won't begin until been pushed back to mid or late 2010.
back to being original designs/sculpts.
|
