|
I have a 28 inch 20 gauge wingmaster barrel and want to cut it to 20 inches and create a slug barrel. i can't seem to find a slug barrel for a pre 1968 20 gauge wingmaster.
Started by shovelhead70 on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at calguns):
What you DO NOT want to....
That is what they were actually designed for use in .
I still do not know if this method allows the use in a smooth bore barrel just like pellets/buckshot can be used.
I missed many of the posts.
barrel? thank you.
|
|
Was just wondering what difference the barrel makes on a .17hmr? Also, due to the thickness of a varmint barrel, what is the deal with getting a moderator? is the barrel just threaded right down so that any .17hmr moderator can be put on?
Started by finreid on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at pigeonwatch):
All my shooting is done on foot so I tend barrel, but changed to the ....
In the least ammo fussy ! so i put its no quibble diet down to the heavy barrel but am sure thats just a standard barrel first I doubt I'd know the difference.
|
|
Can I replace the factory ramped bull barrel that comes with a lightweight Champ Operator with a non-ramped regular bushing barrel? I realize a ramp in the frame will have to be installed.
When I say "I" I mean a competent gunsmith. : )
Thanks!
Started by chrisman17 on
, 11 posts
by 8 people.
Answer Snippets (Read the full thread at 1911forum):
Thanks for your response.
I don't know what a Champ Operator the champion and it's a 4" barrel.
To be anything less than 4.25 inches requires a bull barrel, no bushing.
|
Ask your Facebook Friends
|
What are some pros & cons of the 16 vs. 18 inch barrel on an AR? I am looking to get an AR in a couple of months and I wanted to know what were some advantages & disadvantages of the 18 inch barrel compared to the standard length of regular ARs.
Started by Hecktic on
, 40 posts
by 22 people.
Answer Snippets (Read the full thread at calguns):
Remember that even though the BARREL is a given plinking Wish I would have done it sooner....
Primarily, the 18" barrel buys you the rifle length gas system, which will feel softer to shoot with the 14.5" being super handy and fast on target.
|
|
Just for grins I pulled my ATI apart and did some measuring. Here's some interesting stuff I found out.
The link measures center to center .2835" with the lower hole(the one the slide stop goes in being oblonged .208" top to bottom and .205" side to side...
Started by TN.Frank on
, 24 posts
by 7 people.
Answer Snippets (Read the full thread at 1911forum):
Also, the lugs on the barrel....
It is a key component in how the barrel disengages, I would be watching closely to see if you begin work fine.
To info? Pins are sometimes oblong to better fit the barrel, I have never seen one stretch .003.
|
|
Hi,
What is it meant by US liquid barrel and US dry barrel ? The same apply also to Gallon etc.. ?
Started by Eddy on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at convert-me):
?
Hi,
See explanation in Wikipedia: http://en.wikipedia.org/wiki/Barrel_%28unit%29 Convert.
|
|
Will this work? Since I know real outer barrels has rifling, will the inner barrel still fit?
Started by maduhbee on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at gasguns):
Indeed airsoft barrels range from 8.2mm to 8mm (standard WA inners, but does, as has been mentioned, ....
RS is 5.56mm and air soft is 6mm+ depending on the outside diameter of the inner barrel.
Not without drilling the RS barrel out.
|
|
TSD Glock barrels vs Storm Lake barrels Does anyone know how the Storm Lake aftermarket Glock barrels compare to the TSD Glock barrels? I wanted to buy some spare barrels but they don't sell the TSD barrels by themselves and I want the best money can ...
Started by waddlingweezol on
, 10 posts
by 9 people.
Answer Snippets (Read the full thread at warriortalk):
I don't have a storm lake barrel but I have the TSD G19 Match Threaded Barrel....
Sebastian H, Tucson, AZ.
I cannot speak for TSD but my Storm lake threaded barrel for my 19 is definetly GTG, very well nails, but I don't have one personally.
|
|
Why arent the back to barrels opening on your 4 barrel quadrajet?
, 1 posts
Answer Snippets (Read the full thread at answers):
|
|
Why have I seen pictures of XD and XDMs with a silver barrels and some with Black barrels?
My XD9 has a black barrel.
Could I possibly take that black coat/paint off? If soo how?
Started by GrandmasTampon on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at xdtalk):
But you are probably correct he.
Not whether it was stainless to start with.
Here: DIY Barrel polishing write-up The "black barrels" are carbon steel removing the finish the black off his barrel.
|
