|
Another thread got a bit crazy with [Bear] feats, and so when it was suggested someone make a thread for them, I leaped at the chance.
Celestial Bears! [Exalted, Bear]
Prerequisites: Good Alignment, Any 2 [Bear] feats
Benefit: All bears summoned by your...
Started by NineThePuma on
, 30 posts
by 16 people.
Answer Snippets (Read the full thread at giantitp):
|
|
Due to using a frame that'll only take 40mm bearings (lollipops) I have tried to find solutions for a while for me to use ISIS. Kris came out with his '40mm' shimmed bearings but it seems these are quite a pain for a lot of riders, most notably Tholub...
Started by Sponge on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at unicyclist):
I don't know how tight....
If they made it like that it would be to easy
why go the easy way if you can do it the hard way
i dont see a problem in using these bearings, if they can take to load and stress that are put on it by unicycling That's cool.
|
|
Got home today and noticed a clutch related noise.
When i press the clutch pedal down all the way, theres a slightly rattly sound from the clutch, sounds like a worn bearing. when i take my foot off the clutch, the sound goes away again.
does this sound...
Started by andy-m on
, 17 posts
by 7 people.
Answer Snippets (Read the full thread at southeastscoobies):
My classic was like it for a year or more before I changed the clutch, bit... .
Just tell everyone you have a twin plate mate, they'll think it's really cool and you dnt have to worry, possible release bearing Sounds like thrust bearing mate.
|
Ask your Facebook Friends
|
I was wondering if the dual bearing pullies are really needed for a eaton pullied setup. How many guys have had aftermarket single bearing pullies fail on them? I have'nt seen much info on this.
Started by nxs450 on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at svtperformance):
I went with the meco dual bearing,between just because they made them & with the high belt pressure we put on them they will last longer! Have you searched?
If you haven't seen anything in regards to the stock ones exploding, search and you will....
|
|
I been thinking about when you guys change the orginal input ball bearing on the tranny to a sealed ball bearing. (double sealed both sides). Orginally the open ball bearing allows the tranny oil to lube the outer main shaft seal too. If we install a ...
Started by BigBill on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at farmallcub):
Running the PTO for extended periods of time with out moving the tractor may cause the bearing to be starved of oil, this is why it's important....
Installing a sealed bearing for the front input shaft has no effect on oil reaching the seal.
|
|
I have an hour to kill before my next class. I am sure theres already been some discussion upon this topic, but I dont have the time to do the research right now. I just want to share some light on this topic. If this is helpful to you then stay tuned...
Started by drewski1990 on
, 14 posts
by 7 people.
Answer Snippets (Read the full thread at mazdas247):
Not trying to discredit your thread, but ball bearing turbos do still use oil....
Hopefully to lessen the drag..
Good info i got a t-25 sitting in the garage as a spare and i polished the turbine stem once i figured it floated in the journal on oil .
|
|
Originally Posted by webkinz415 I LOVE This Pet!
Although Since The Sun Bear Is A Non-Fiction Bear And
Already A Webkinz, I Would Call It The Sensational FIRE Bear. Oops, forgot that!! Thanks for letting me know. I'll change the name.
Started by Priceless on
, 10 posts
by 10 people.
Answer Snippets (Read the full thread at webkinzinsider):
I would want this bear FOR SURE what a beautiful job you did of making it's PSF and PSI You.
|
|
Greasing trailer bearings doesn't work...thinking about bearing buddies I have a 1996 Ranger Trail trailer for my Ranger R70. I have owned the boat for about 6 months and am trying to grease the bearings. There are instructions, but, that has not been...
Started by diehardmason on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at iboats):
Re: Greasing trailer bearings doesn't work...thinking about bearing buddies How often are you trying to grease the bearings? Re: Greasing trailer bearings doesn't work...thinking about bearing buddies Bearings....
|
|
Does any one know why wheel bearings vary from such different prices. I have seen some on jc whitney for as low as 11 each all the way up to 130. And some say inner wheel bearing? The ones on ebay are like 80 I believe for the Pair.
I guess my main question...
Started by 1cleansinglecab on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at ttora):
They ....
If you dont need to do the rears why replace it .
Go with whatever you think boss.
It all depends whether you support america or go asian man like said above .
Made in U.S.A Also a big difference between the 2wd and 4wd bearings.
Chinee vs.
|
|
I am doubting an initial diagnosis I made regarding front end vibrations in my 05 4x4 that has a 2" lift. Thought it was the front diff bearing that's been discussed on here, but now thinking it could be a wheel bearing.
Here's the particulars:
-Pretty...
Started by eeberleeber on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at tacomaworld):
Here's ....
Thought it was the front diff bearing that's been discussed on here, but now thinking it could be a wheel bearing.
|
