|
Posted 16 April 2007 - 08:56 PM
Hey there guys. Over the last few months Ive had scores of people asking me to do a tutorial on how to install speakers correctly into the doors of the R33 Skyline. Well we (obviously) had to wait for another R33 to come...
Started by Fhrx on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at skylinesaustralia):
They show the passenger side door plug kebabs' :sorcerer:
You can deaden....
That i should go buy some? Posted 17 April 2007 - 11:39 PM
if you want to get the best out of your audio to the other thread in CAA so I thought I'd add them here too.
|
|
Hey there guys, a few people have asked me over email and PM about how to get decent speakers into 323 / Astina doors. So without further ado, this is the procedure for doing the doors correctly.
Step one: Take one original door complete with factory ...
Started by Fhrx on
, 20 posts
by 14 people.
Answer Snippets (Read the full thread at astinagt):
How much in at @rse to get off to install my speakers Hmmm, if I was doing the rear door speakers again I would just does it cost for this....
Thats the best install i've ever seen makes everything else seem very dodgy and cheap.
|
|
Whats the best kit to get for vertical doors?
Started by eklypised on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at camaro5):
If you are looking for a kit let me know my... .
Easy to install easy to operate.
I personally use there kits and sell there kits.
Pumped! The best kit on the market is the vdi kit, they hold all the patents for the kits.
This past Thursday.
|
Ask your Facebook Friends
|
I'd like everyone's thoughts about the preferred method of installing a prehung solid core door. Is it better to install the door frame with or without door slab in place?
Started by WoodmanFL on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at diychatroom):
Install jamb as above but leave the ....
Attach hinge side and then shim other side so gap is even all around door.
Then install door in jamb and install in opening.
Them with a long level or level and straight-edge.
Related shopping results:
|
|
I know folks have done this type of an install before but I decided I wanted to share my install.
I purchased a $30 opener and coded to my door.
I took the opener apart and soldered/wired a $.99 momentary contact switch across the circuit board connections...
Started by golfmajic on
, 10 posts
by 9 people.
Answer Snippets (Read the full thread at hdforums):
Why don't you just gak it a couple of times in the driveway and... .
Didn't install in the right side pouch?
Curious is all.
|
|
I have a 2008 Rubicon with the stock open gas cap design and I would like to install a locking fuel door. Do I need to add a new gas filler housing unit along with the locking door or is there a housing unit with screws hidden behind the white stock trim...
Started by harleytroubl on
, 6 posts
by 5 people.
Answer Snippets (Read the full thread at jeepforum):
The mopar ....
Piece 'O Cake to installI have the Mopar door in black and the kit had everything you need.
The Mopar door is the best out there.
And I don't think the AMI does.
|
|
I had to deal with the holes being over sized in both the inner and outer panel. So I found a better way to attach the door rests.
I drilled a hole in the inner panel and installed a 1/4 20 nut zert. It came out so well I was shocked. That inner panel...
Started by GMR-PERFORMANCE on
, 9 posts
by 4 people.
Answer Snippets (Read the full thread at 67-72chevytrucks):
I could use that to install my headliner! thanks.
That's bad ass.
It rocks.
I plan on using the 10/32 units in my for more than a decade .
It will allow you to install super clean fasteners where ever you want.
|
|
What is the best caulking to use to seal a window? i got some Sika Construction Sealant from HD as I've been real please with their other products (particularly Anchoring Epoxy, that thing rocks my world) but was wondering if there is anything better....
Started by amakarevic on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at diychatroom):
Sounds silly, but it really.
Quad on every brick and stone install that we do.
|
|
I read on the manual it says start with left hand side, but it looks like passenger side.... i figured left hand is driver side (US vehicle)
what is the best way to install and uninstall soft top without damaging the seals and cable..
clip in pass side...
Started by rijowysock on
, 20 posts
by 14 people.
Answer Snippets (Read the full thread at lotustalk):
The question isn't "how do I" it is "what is the best way it is documented that one side....
Hand is driver side (US vehicle)
what is the best way to install and uninstall soft top without remove and install an Elise Soft top.
|
|
I was wondering how I would go about making specker pods for a couple of 8 inch woofers in my door pannels of course it would be one in each saide I am wanting to do it nice and clean and tastefully
Started by Manofthestreet on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at probetalk):
Then make in the door? for MOAR BASS!! lol.
Enjoy the best location would probably be where the factory speaker sits.
With the fiberglass work.
|
