|
Are fewer blades always 'faster' than more blades? I hate when I give general, well-established guidelines to people and then they refute them because some guy told them something different, which requires me to go into more detail, but also know the ...
Started by Philster on
, 23 posts
by 12 people.
Answer Snippets (Read the full thread at iboats):
There was also reasoning that with multiple blades, the efficiency of each blade was less but overall prop became more powerful, the blades became too long (risking prop-strikes) and also, the blade tip speeds blades....
|
|
P1010553.jpg P1010554.jpg P1010556.jpg
First pic-Rajah 1 and rajah 2
Rajah 1 and box,lanyard,extra clip+ hardware-***SOLD***
Rajah 2-same included-***SOLD***
both Rajahs have no bladeplay,beautiful lockup,never resharpened,cosmetic scuff on bolster of...
Started by Spartanbuddha42 on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at jerzeedevil):
Darrex@darrex.net P1010606.jpg P1010607.jpg P1010608.jpg P1010609.jpg
THE FIXED BLADES(top 2 photos)
left vertical homes
The Monster Stilleto-15" overall,no bladeplay,marked"stilletto siciliano"blade not centered lever action ,blade....
|
|
How tight do you tighting the main blades and tail blades thanks
Started by sgtrex on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at helifreak):
If you had the rotor head in your hand and the main blade was attached, it should be tight enough so that the grip will hold the blade straight out in the air, but if you tapped the rotor head gently on something the....
Think of it this way.
|
Ask your Facebook Friends
|
Anyone notice that the HS22 blades take at least 3-4 minutes to get to booting the OS?
Is there anything that can be done to get it through the BIOS faster?
Started by romant on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at serverfault):
Maybe 60-90 seconds....
This is always slow.
I'm not familiar with the HS22, but we have a Dell Blade Centre, and I'm guessing that the reasons with, in a blade centre, everything is high quality, and high quality parts have always taken a long.
|
|
Hi,
Im looking for a set of FBL or possibly FB main blades for my 700.Must be standard 4mm hole and in v.good condition.standard 3D blades wanted,not interested in F3C or semi symmetrical blades thanks!.
craig
Started by exiged on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at rcheliaddict):
I have a set of 700mm Sab red devils 3D Blades if you are interested VGC Are they fbl?,how much.
|
|
Various CF 325mm 450 sized heli blades SOLD
250mm microheli blade SR CF blades
2x Align T-rex 450 aluminum booms, 1x CF SOLD
T-rex 450 torque tubes SOLD
New never used CY stubz CF flybar paddles SOLD
New never used CF T-rex 450 tail blades SOLD
Blade ...
Started by M52 POWER! on
, 9 posts
by 4 people.
Answer Snippets (Read the full thread at helifreak):
Do you still have the 450 blades and how much? Payment sent for:
*Various CF 325mm 450 sized heli blades
*2x Align T-rex....
Sent PM about 450 blades, tail and I'll take the mcpx fins Sent PM about Stubz Replied! Payment sent for Stubz.
|
|
After comparing my KBDD tail blades with Eflite's V2 tail blades on my heli, I found that the v2 tail blades are noticeably better than the KBDDs.
While the V2 blades hold almost perfectly when ascending at maximum power, the KBDDs just can't keep up ...
Started by MetalStorm on
, 10 posts
by 8 people.
Answer Snippets (Read the full thread at helifreak):
Has anybody else had a similar experience and is there any way to give the blades more pitch? I really like how visible the KBDD blades are and would like my main blades - orange KBDDs - and my tail blades to match."
My experience....
|
|
**All blades have been spoken for **
I recently bought a second pack of the Personna DE Blades from Ebay which are commonly called the " Lab Blue " blades. Now some folks say they are nearly identical to the Personna Medical's DE Prep blade, except for...
Started by 5Savages on
, 16 posts
by 11 people.
Answer Snippets (Read the full thread at theshaveden):
Thanks! I think that makes 3 lol, and Iradke, please send me a PM with your address!... .
I've used the med prep blades and would like the opportunity to do the lab blue blades, I would like the chance to if your willing.
I'm very interested.
|
|
FT SI'S for Blades wtt my 00 si's with 95% on all fours for gsr blades lm
Started by Elflako92 on
, 14 posts
by 5 people.
Answer Snippets (Read the full thread at tamparacing):
I got 15" white ssp..
Bumpppp tt ttt bump clean Sis bump rep.ttt ttt How much would yu let them go with steelies and hub caps 813 638-6262 Hmu ft only ttt bump ttt txt me 407-719-7955 Text me 813-545-5624 .
|
|
DeWalt 13" Planer Blades for 735 #49.98 KW Lowes is selling the DeWalt replacement blades for the 735 planer for $49.98, normally selling for $99.
Started by macquanski on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at canadianwoodworking):
Good to know, thanks! May have to wander on over Re: DeWalt... .
Re: DeWalt 13" Planer Blades for 735 #49.98 Originally Posted by macquanski KW Lowes is selling the DeWalt replacement blades for the 735 planer for $49.98, normally selling for $99.
|
