|
Hercules motor control board-mods? SO I've just bought a Hercules and of course good enough never is. Has anyone ever performed any successful mods on one, or a Valhalla. Suggestions please, I'm thinking PSU side first before looking at what comes out...
Started by sq225917 on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at pinkfishmedia):
"hercules motor control board there was anything electrically relevant at the back end of a Mose, just connections to the motor, an IEC inlet of....
I went for the Mose Hercules because of my requirement for 45 rpm .
By an Armageddon.
|
|
1990 Safari, Intermittent wiper problem.
My van suffers from the wiper problem where they run a cycle when I use the turn signal lever. Not every time, maybe 30% of the time. And usually the wipers run once when I start the van. I have replaced the turn...
Started by 98cirider on
, 20 posts
by 5 people.
Answer Snippets (Read the full thread at astrosafari):
The dealer wants $152 for one and I can not seem to locate an after one out of four ....
So, I pulled the Pulse Board out and lightly sanded the contacts with paper the Wiper Motor Pulse Board.
And the wipers fired off.
|
|
I am not sure where to start here so I will start at the beginning. I have a CPC 1100 GPS (XLT) that I purchased in 2007.
The scope was working fine until I tried to connect it to connect it to my ThinkPad laptop (Windows XP) in December. I could not ...
Started by guitarman on
, 21 posts
by 5 people.
Answer Snippets (Read the full thread at cloudynights):
I asked him if replacing the motor control board could be a solution to the problem a new motor control ....
He told me that a reading of 1.00 on the motor control board is a red flag because the original to Celestron.
|
Ask your Facebook Friends
|
Is there such a thing as Power steering on a boat with an out board engine. My pontoon boat is like a tank when the boat is moving.The faster I go the worse it get's.The steering is ok when I'm just setting still.It's a 90 hp Merc on a 24ft pontoon boat...
Started by Silver Eagle on
, 12 posts
by 9 people.
Answer Snippets (Read the full thread at iboats):
Http://www.iboats.com/Complete-Marin: Is there such a thing as Power....
Hydraulic steering system info in link.
You can add with an out board engine.
Re: Is there such a thing as Power steering on a boat with an out board engine.
|
|
I received the Hawk RC 10A ESC and an Oversky HP05S (from Astroid) last week. Set it all up with a v2 3-in-1 (ESC hooked up to main motor port) and I seem to be having a lot of difficulty. I've got a dual-coreless tail, shows mild wagging at about 2hz...
Started by GeneralAntilles on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at helifreak):
motor mosfets are out of the loop when you solder to the resistor on the back of the board..I have and brushless setups), but the only v1 board I've got has got a burnt main-motor MOSFET fine on the V1 board.....
|
|
Animated Ouija Board (Vent Motor) PART 2 – 08-31-2011, 11:32 AM Animated Ouija Board: PART 2
STEP 5: Linking It All Together
A: The motor will be mounted onto the bottom board using two 8-32 X 1-1/2 inch machine screws. Measure and mark on the bottom ...
Started by DaveintheGrave on
, 10 posts
by 6 people.
Answer Snippets (Read the full thread at halloweenforum):
I need to find my son's....
Got a few strange the glow.
Moss How-To 08-31-2011, 09:19 PM Perfect timing I just got my board and motor today! Cant wait I got my Ouija board free by sending a shout out to my friends on Facebook.
|
|
I have a desktop CNC router that has been working great, but has started to run rough. I don't know what else to call it. It's started to produce inconsistent results, with non-repeatable errors that make the cuts rough and unacceptable. I've tried everything...
Started by mickelsen on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at cnczone):
Does the problem affect all the axis....
Gerry
Mach3 2010 Screenset
http time.
My company fixes spindles, ballscrews/lead screws and servo one? If just one, try swapping the motor from a good axis.
Yes they will,as all motors wear out.
|
|
I was trying to cut some aluminium last night, but my mill's been stalling recently, and it did it again last night scrapping the part
I was cutting 12mm wide (0.5") and 1.5mm deep (0.06") with a rougher, and with my mist coolant soaking everything nicely...
Started by digits on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at cnczone):
Even then well designed it is possibly brushes not seated... .
The load on the motor should be trivial.
This could be a motor / controller issue but don't dismiss something happening with the bearings.
That you heard the motor bog down.
|
|
Paik11 This board has become a Politico Board and I hope it hasn't driven away el_toro and others.
Started by My Raging Bull on
, 22 posts
by 1 people.
Answer Snippets (Read the full thread at quote):
How dumb well, spending was out of control, the Bush low taxes (A good thing) and our civil liberties have the life out of obama while delivering....
Folly, the politicians on this board elected that idiot GW for not one but two terms.
|
|
Hey thanks for checking out my BST! You can see I do have some feedback here and I also have a crap ton of ebay feedback that can be proven if required.
I am offering the following:
Modded Ring of Light boards for Phat consoles.
I have every color that...
Started by itwontfixitself on
, 3 posts
by 1 people.
Answer Snippets (Read the full thread at ps3scene):
|
