|
*bnib fd2 " ctr " rrc intake manifolds (plenty in stock) $420.00 us dollars shipped p/n #17100-rrc-000
*bnib rbc intake manifolds (plenty in stock)$270.00 us dollars shipped p/n #17100-rrb-a00
*bnib 07 and up accord v6 throttle bodys (instock) $130.00...
Started by JUSTIN@AUTOFAIR on
, 20 posts
by 7 people.
Answer Snippets (Read the full thread at civinfo):
P and yes it is $420.00 shipped to the uk.. .
#17100-rrb-a00
*bnib 07 and up accord v6 throttle bodys (instock) $130.00 us dollars shipped already modified.
|
|
Venting bodys? Any one here making holes in there bodies to reduce the dreaded parachuting effect ? I've just made a few below the spoiler on my Manta body. Yet to try it out though!
Hoping it will make a difference when I try to race next. You guys seen...
Started by crazee horse on
, 18 posts
by 13 people.
Answer Snippets (Read the full thread at traxxas):
Hopefully performs better than it looks haha! Use less brakes the parachuting effect is kind of hard to stop at least for me my proline raptor svt body....
It looks bad but I'm about to go test it .
I just finished my vents on my stock body...
|
|
V6 throttle bodys...
might be worth it to someone (not mine)
http://www.ebay.co.uk/itm/Vectra-V6-...item4ab2e15866
Started by Mad cornish pastie on
, 10 posts
by 6 people.
Answer Snippets (Read the full thread at vvoc):
|
Ask your Facebook Friends
|
I have yet to see a 4th gen meet up in fresno and thats just disappointing. So if you live in fresno or the surrounding area (clovis, fowler...ect) let me know and we'll get something going. I have a 2000 trans am (pewter) m6 with bolt on's.
I've seen...
Started by trans_am_man on
, 20 posts
by 8 people.
Answer Snippets (Read the full thread at ls1tech):
Just give me a time....
I wish I was around for this we will have to do this again during the summer when I get back home Aye, when? I am down, I have an '02 SOM WS6 on black C6 ZR1 Wheels, I normally go to and from Fresno state alot .
Bump for a good idea...
|
|
Me and my car club went out today, thought I would share a few pics with my pic loving MTF family
Started by 89YT12 on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at mytractorforum):
In by owning one while you were a member but we like all f-bodys to roll and hang with us, we even got.
|
|
So I'm doing restoration work on my Stang. Nothing in the engine, just body and interior. Engine ran fine up until a couple weeks ago. I started it and let it run for a while to keep things fresh and didn't have a single problem. When I went to start ...
Started by mikedero08 on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at srtforums):
Mark....
The pcm never goes bad unless it gets wet somehow .
Its the module in the dizzy for sure.
Pickup coil? Just throwing the obvious out there first sir .
|
|
Rustler bodys Does anyone know if you can put a nitro rustler body on an electric one. Because they seem to cost lest.
Started by djbird1xx on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at traxxas):
Nitro ....
Pede 4x4 MMP/2400 ** Slash 4x4 MT MMM/2650 The rear shock tower on a nitro rustler is about an inch farther back than the electric rustler .
Anybody there? I would say yes, but have in mind some nitro bodies have an opening for the motor.
|
|
Throttle bodys and manifold 106 gti selling my throttle bodies and manifold off my rally car, upgrading to bigger bodies. here is the ebay link
http://www.ebay.co.uk/itm/2209479317...84.m1555.l2649
Started by cassellsmotorsport on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at 106owners):
Re: throttle bodys and manifold 106 gti how much would you let the itb's setup go for mate? or you just going to let the auction run? Re: throttle bodys and manifold 106 gti Is it a standard 16v 4-2-1), Silicone Hose, Powerflex Engine Mounts....
|
|
Any one got any 38mm velvet shock small bore Bodys they want to sell.Please PM me with what you have got
Started by AndrewCaunt on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at oople):
Went really well today....
Where were you today??? got a spot on setup for the FS mate. .
Give me a buzz tomorrow..
As Mike says im sure we have these in...
Andy...
For FS I assume, have you got w5195v shock kit? Will have a look mate .
JE spares have stock.
|
|
Ok so ive been creeping around and ive noticed people convert there intake throttle bodys to throttle bodys that just stick out instead of going onto a tank. cold air intake or something like that? whats the advantage of this anyone know??
Started by GreenCamaro13 on
, 10 posts
by 2 people.
Answer Snippets (Read the full thread at thirdgen):
Do you mean putting a Cold Air Intake on the car? Rather than leaving the stock air box and filter on it? I guess a picture of what your talking about would help lol yes the cold... .
Im not sure ive seen anybody make there throttle body stick out....
|
