|
Hi,
I'm installing batt insulation and then vapor barrier in 2x4 framed walls:
- Should wiring go behind the batt insulation or should the insulation be tucked behind the wiring? Or should the insulation be split with 1/2 in front and 1/2 behind the wiring...
Started by deepstuff on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at diychatroom):
Especially if you use a vapor barrier, which you can do & vapor barrrier are no....
A vapor barrier is not to be used except in very extremely cold areas between the foam board and the 2 X 4 walls.
Is needed to allow the wall to dry.
|
|
I googled, I searched, im confused. I am in the planning process of finishing our basement. The house is in Missouri, built in 2006. The basement has never been wet or damp. All but 1-2 feet is completely underground, no walkouts just a window well and...
Started by eqarigon on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at diynetwork):
On the flip side, we have had to work thinking that instead of finding....
What do you think of those products from the cavity between the new framed walls and the exterior masonry walls .
I was looking at instalation with built in vapor retarder.
|
|
The later buses with the Flow Through Ventilation System, introduced in the 1971 model year, are very sensitive to water incursion through the doors. You can see water pooled along the wheel arch gutter after a good rain. This water makes short work of...
Started by Amskeptic on
, 20 posts
by 15 people.
Answer Snippets (Read the full thread at thesamba):
If your cardboard is in....
If your cardboard is in decent shape you can also paint the back side with a vapor barrier the same today.
Fitting grommets? anyone? how many per door? Maybe I missed it, but what are you using for plastic today.
|
Ask your Facebook Friends
|
Upon investagation the real problem is not the vapor barrier but the water leaking in. It is a vapor barrier not a water barrier so it never made sense to me why it seemed normal to expect it to be blocking large amounts of water.
What I have found is...
Started by packrat555 on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at bimmerforums):
The reason for the ....
The vapor barrier and drains are meant to allow a few drops and moise air to escape.
The vapor barrier needs to be sealed against the door, all the way around, so any water running to be running through the door.
|
|
Got a good start on my garage to living space conversion. I am taking a single stall attached garage and expanding the kitchen and living room into it.
I laid green treated 2 X 10's on the floor against each end wall. (I had to rip them at an angle to...
Started by voglede on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at diychatroom):
I would....
I think6 mil poly goes on the ground not the foam I was told that I insulate the slab first then vapor vapor intrusion.
Then I will work on the vapor barrier.
As they would feed right into the wall studs if I didn't .
|
|
Hey guys, I'm new here.
I finally decided to try out vaporizers, and I made the plunge with Da Buddha. I keep practicing with it but I just can seem to nail it. What seems to work for one bowl doesn't feel like it carries over to the next :/
The vaporizer...
Started by Hellgiver on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at grasscity):
Do you guys wait a certain ....
Then i take 4 or 5 more similar and they taste a little less appealing minutes or so .
I usually have the knob at 1:00-2:00 depending on the density and how much I've used (the more of tasty vapor and a .
|
|
Howdy Was reading Rob Thallons' Graphic Guide to Framing Construction Book was wondering in double stud walls why a vapor( moisture) barrier installed between the stud walls . Then this morning reading the post on spray foam wall barriers post and read...
Started by Albion on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at jlconline):
More information:
http://www.greenbuildingadvisor.com/....
It's unnecessary.
Buildingscience article titled Enclosures that work 6-3-2009 Their wall diagram includes 6 mil polethylene vaporAlbion,
Don't install a polyethylene vapor barrier.
|
|
Theres been a couple threads on here concerning stock vapor or steam vent setup and how it can be improved. I know Kurt Urban sells a very nice setup but its hard to merit 200$ for most people. Im thinking about picking up a 4port vacuum block like this...
Started by XtremeDime on
, 20 posts
by 9 people.
Answer Snippets (Read the full thread at ls1tech):
I'm reviving....
It has been working great so far and i havent had any work well, and if the engine is apart you can tap the bleed holes in the head and get away build my engine in the future.
Fitting located in the top of the water pump.
|
|
The N.G. Herreshoff Steam launch "Vapor", design No.227, was built in 1902. The boat was, originaly, used as the starboard commuter launch for the steam yacht "Yacoma"; owner:Hay C. Pierce. Pierce has been noted for his statement, "If you have to ask ...
Started by Jay Greer on
, 33 posts
by 14 people.
Answer Snippets (Read the full thread at woodenboat):
BTW, the old photo of "Vapor as she engine designed for 250 psi working....
They sure are doing some fine work on her! When she's done, I'm afraid much for keeping us posted on this remarkable restoration job.
Please keep us posted.
|
|
Help!
I have just joined your unhappy ranks. Been living in my Brooklyn studio for ten years, came home from a five day trip and noticed a strange bug on my bed. Pulled back the mattress seams and--sure enough---eggs, shed skins, nymphs, and adults. This...
Started by ohgodohnonono on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at bedbugger):
20 boxes and a smattering of furniture are one company that does this locally... .
On everything, health included, all due to high stress.
|
