|
On Mon, 19 Jan 2009 18:30:02 -0800 (PST), Doobie Keebler <kooper.db@gmail.com
The bottom line for Bush's 2005 inauguration, including the cost of
security: $157 million.
(... and that was going into his SECOND term, for crying out loud.)
So, anyway...
Started by Doobie Keebler on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at omgili):
PermaWar and Bush Bank Bailouts time for the markets, getting Bush Sr....
See, I'm like this _HUGE_ fan of Peace and Prosperity .
It really Era.
The right wing all imploded and shit itself.
Screw ups under Bush's leadership.
|
|
On Tue, 23 Jun 2009 13:12:59 -0700 (PDT), edspyhill01 <edspyhill01@gmail.com
Hey, the Bush tax cuts cost the US $1.3 Trillion. Rescind the Bush
tax cuts and we can pay for healthcare for everyone in the US.
Started by edspyhill01 on
, 28 posts
by 11 people.
Answer Snippets (Read the full thread at omgili):
The
biggest record ....
We could have been having record tax
revenues all 8 years of GW Bush's presidency, but we didn't.
Record tax revenues are routine.
All the way back to WW II.
And GHW Bush's
presidency, Reagan's, Carter's, etc.
|
|
I went to Tuffy's Automotive (Colonial - Ft. Myers Fl) and they told me it would be $450.00 to replace 1 trailing arm bushing.
Their computer showed 3.5 hours to do the job and they wouldn't budge on the cost. I tried to explain to them, I just wanted...
Started by SGOS252382 on
, 19 posts
by 11 people.
Answer Snippets (Read the full thread at camaro5):
I'll definitely never go back to that shop..
I tried to explain to them, I just wanted 1 bushing replaced for the cost they were trying to charge me.
And they wouldn't budge on the cost.
|
Ask your Facebook Friends
|
Hey Guys,
As most of you already know, i've had a bad vibration in my TTG, over the last three months i've replaced the following with no avail.
-Half Shafts
-Changed all three rear bushes with Nolathane.
-Changed two front diffbushes to Nolathane.
-Changed...
Started by captin-zaneo on
, 9 posts
by 7 people.
Answer Snippets (Read the full thread at fordforums):
Is this where the 3rd bolt goes through, towards the drivers side? Cost and relative difficulty removing it mate? Yea mate,
it cost me $79.80 trade price i think they are about $100
Gen Ford the part all three diff bolts and jack the diff....
|
|
Hey Guys,
As most of you already know, i've had a bad vibration in my TTG, over the last three months i've replaced the following with no avail.
-Half Shafts
-Changed all three rear bushes with Nolathane.
-Changed two front diffbushes to Nolathane.
-Changed...
Started by captin-zaneo on
, 9 posts
by 7 people.
Answer Snippets (Read the full thread at fordforums):
Is this where the 3rd bolt goes through, towards the drivers side? Cost and relative difficulty removing it mate? Yea mate,
it cost me $79.80 trade price i think they are about $100
Gen Ford the part all three diff bolts and jack the diff....
|
|
Two of my SDs have loose fit bushes in the crankcase.
Do I need new bushes or can they replaced with Loctite?
Thanks,
Jan
Started by Jan on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at saving-old-seagulls):
Then gently apply....
If the bush is still a firm centres on a lathe.
Compound, as would be used here, will let go after a short time when the bush is loose to start with and there is rotational and side loads coupled with heat and vibration.
|
|
On Tue, 20 Jan 2009 08:03:50 -0800 (PST), "edspyhill01@yahoo.com" <edspyhill01@yahoo.com
Ha ha, rightwingnuts - burned by Drudge AGAIN!!! BRraaa HAhahaha!
Media make false comparison of inauguration costs
Summary: Leading up to President-elect...
Started by edspyhill01@yahoo.com on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at omgili):
That article you quoted.
Think Bush's inauguration costs were anywhere
close to Obama's.
|
|
I checked the outboard rear wheel bushings at 1,644 miles. Lots of slop and no grease. I cleaned the bearing carrier and bushings with compressed air and nothing but dust. I installed new bushings and shafts and added grease fittings. The Yamaha Rhino...
Started by hondabob on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at rzrforums):
The RZR 800 has nearly IN REPAIRS IN 1200 MILES GOOD THING I DO MY OWN MAINTENANCE POLARIS SHOP COST IS 70 BUCKS AN HOUR SPENT OVER 500 IN REPAIRS IN 12....
The bushings and shafts cost about $50.
Easy to install the grease fittings.
|
|
Hi guys - well I found the clunk in my rear suspension. Front bushing in the right rear trailing arm.
After paying for a machine shop to press the old bushing out and new in are are you really saving any money compared to a new arm with bushing from IAP...
Started by tdskip on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at alfabb):
Just remember to be safe, block both front wheels and use was selected to fit just inside that... .
Only cost, cost is minimal and it's not too difficult.
It's been a few years since I did my rear arms, but I did it all myself and went to poly .
|
|
Hi Im new to the forum but not to ATVs. I have a 08 or 09 RZRs with about 3K on it.
I just noticed play in the rear end bushings.
My question is at almost 4 times the cost of other kits containing all the bushings needed for both front and rear swing ...
Started by bobp on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at rzrforums):
Every single parts place I checked when I bought a new but they are switching companies and the cost should be less even though it still showed it as $19 for ground.
Which puts the Delrin ones at 4times the cost.
|
