|
We have a number of these but only use 1 fireplace.
Was thinking of filling the flues entirely with EPS pellets to stop airflow and capping the chimneys. Would this work?
Regarding the fireplace we use, the chimney stack will have one dormant flue and...
Started by buyingabroad on
, 18 posts
by 4 people.
Answer Snippets (Read the full thread at askaboutmoney):
Would be similar to an uninsulated solid brick external wall?
If we put in a stove with a flue up the flue and brings tar deposits to the chimney breast in the rooms below - it is rather difficult PARTIALLY BLOCKED CHIMNEY....
|
|
Hi everybody,
Just looking for some advice about connecting the flue to the multifuel stove. Well more to the point, how to actually seal it. I've tried a few different products with varying success.
The stove has been in a couple of years now and the...
Started by Jack_regan on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at boards):
DO NOT USE HIGH TEMPERATURE SILICONE TO SEAL A STOVE AND FLUE level as this....
If the stove is operated at this optimum level reading this will learn from my mistake.
Which equates to approximately 250C at the flue pipe.
|
|
I have my oil furnace venting in maonary chimney (forced hot water system), can I vent a hand fired coal stove in same chimney? Coal stove pipe would be below furnace pipe, furnace pipe has baro damper.
Started by sigs48 on
, 15 posts
by 12 people.
Answer Snippets (Read the full thread at nepacrossroads):
The power vent would only have to run chimney with a certain sized flue outlet, but I don't know how it is handled when two appliances have), but they all go in....
To mind, and then use the existing chimney for the coal stove.
|
Ask your Facebook Friends
|
Code in Massachusetts says all stove pipes have to be 2' higher than anything else within 10'. For this reason, most people with steep roof pitches have stove pipes or chimneys exit at the ridge, or very nearby, meaning less pipe is needed outside. Slighter...
Started by danf26 on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at construction-resource):
Many stove manufacturers details have a max length of uninsulated pipe to maintain up to just below the ceiling....
Just my 2 cents, but couldn't you put the stove at the eave wall, where you want it, run the pipe snow going by.
|
|
I am in the process of buying a 30' x 40' building with a 6" poured radiant floor. The floor has a five loop pex manifold but does not have a boiler or a chimney. A power vent is not an option because I will also heat with a hand fired stove.
Would you...
Started by PC 12-47E on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at nepacrossroads):
I put a single flue in using 16The possability....
Is the logical one, because you could have the chimney with 2 or 3 flues, look terrific, and have a flue in the barn directly on a 4" slab--no footer under the chimney.
|
|
OK....I might get a allot of eye rolls for this one but it doesn't hurt to ask....I have a existing brick open wood fire place. From floor to top of brick is 30inches. Yes I have had the chimney checked out and according to the guy it looks brand new ...
Started by baseburner on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at nepacrossroads):
For your answers The stove pipe going up the chimney would be going past the smoke shelf where" a foot and a half down from the back of the stove, then back, then to a 90deg angle up the chimney....More of a 6" flexible....
|
|
Folks,
have got 4 quotations from stove installers to install a stove.
My idea was to cut out a bigger hole where the fireplace is an to set it back into the opening. Using top exit the flue would be straight up.
2 installers with 20 years experience ...
Started by johneym on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at boards):
Soot is a carcinogenic substance b.t.w..
Further into the stove and the flue pipe.
Running down the chimney into the stove, flowing out at the flue pipe joints.
|
|
Posted 13 April 2012 - 09:22 PM
I was a good boy last year and for Christmas Mrs S brought me a Frontier Stove a great bit of kit for cooking on and keeping warm it has proved it's worth this week, and scratches the itch of having a fire even on a 'normal...
Started by JasonG4110 on
, 16 posts
by 7 people.
Answer Snippets (Read the full thread at lr4x4):
The other bit to go with the chimney, let enough cold air into the tent to allow the stove to burn clean as it was in a wooden building the problem with that is the flue packs up inside the stove so I want hole for the ....
|
|
Good morning everyone, this is my first post so bare with me and ill try give as much detail as possible.
I moved into my house last october, we stripped walls of wall paper and this one wall came off no bother so i thought nothing of it. A few months...
Started by DavidMcCarroll1 on
, 12 posts
by 4 people.
Answer Snippets (Read the full thread at ultimatehandyman):
When the roofers removed the top parts of the stack/chimney, what did they do with the rubble etc, ?
Did they drop it down the ....
The only suggestion at the moment is, the damp is tracking from outer wall, and the flue could be bridged.
|
|
So our DS 1500 Circulator did a fine job during its first winter and with the new stove we wanted to set it up for the summer months and protect the inside of the stove from the harsh months of high humidity and rust formation.
First we obviously cleaned...
Started by Rex on
, 15 posts
by 13 people.
Answer Snippets (Read the full thread at nepacrossroads):
Does it smoke much....
I am also using a 40 watt light bulb inside in the chimney vent/flue passages and tie or tape it to the on/off switch.That way whoever turns.
And LPS 3 all surfaces inside stove and chimney pipe.
|
