Connecting Inch Pieces Pipe

Tuesday, March 31, 2009 - 6 Posts by 2 People

That is not connected. Other dual exhaust can be where the two pipe come back and at some point they mean. True duals is an exhaust system with one exhaust pipe for each side of the engine is normally lower than the connecting pipe can be off set by installing something with higher flow

Monday, August 17, 2009 - 25 Posts

So I know all the reasons why a 3 inch single exhaust is ideal for a high hp turbo setup , but I love dual exhaust too much to give it up, are there any 3 inch dual exhausts available that function from 3" to the 2 smaller dual outlets. In other words if the 2 outlets connecting to the 3" pipe

Wednesday, April 08, 2009 - 13 Posts

There and connected to the network so she can use the printer in the house from there and the printer to get some antennas that would cross the gap and keep a stable connection instead of the standard ones for: Lay out the straight pieces of PVC pipe in the ditch, and stick them together using the straight

Saturday, March 21, 2009 - 10 Posts by 6 People

I need to re-pipe my hunting cabin. It's currently piped with 3/4" gas pipe underground lines, and tie back onto the 3/4" gas pipe with a 3/4" pipe that will run the length of the cabin " with a shutoff, then a 18" flexibl line connecting the vertical riser to a 3/4" pipe that runs

Thursday, September 17, 2009 - 16 Posts by 6 People

pipe for a few inches and then it expands to a bigger 3.5" pipe and is welded to it. Where can of a flange with a pipe section attached that could slip over the existing Veilside exhaust pipe and also . they will simply measure the 2 pieces of pipe and they can flare out some pipe to fit over each part...

Wednesday, May 13, 2009 - 9 Posts by 6 People

Yesterday while clearing a washing machine drain with a snake (auger) I picked up a piece of black . It is approximately about 1.6" wide, and about 4 inches long. It has a clean perpendicular cut at one end Roberto, welcome to the Forum neighbor pictures would help but I doubt it's a pipe liner. More

Monday, June 01, 2009 - 11 Posts

Finally Fred Beans Parts offers this simple adaptor flange that will allow you to connect a 3 inch downpipe to a stock cat-back exhaust. Or any cat-back exhaust that tapers to 2.5 inch at the flange for the invidia dp with stock cbe? do i need to buy the one with all 3 pieces?NJLGT, you will only need

Friday, April 10, 2009 - 15 Posts by 5 People

Will connect the down pipe to the cut pipe. Gently used. $250.00 picked. Or $285.00 shipped via Paypal... 2.5 inch Race TDI Downpipe for Golf, Jetta 4 and New Beetle (for std clamping sleeve) 251.232RN NON 2.5 inch Race TDI Downpipe for Golf, Jetta 4 and New Beetle (for std clamping sleeve) 251.232RN NON Cat Race Turbo Diesel...

Friday, April 10, 2009 - 15 Posts by 5 People

The clamp pictured below will connect the down pipe to the cut pipe. Gently used. $300.00 picked up... 2.5 inch Race TDI Downpipe with Magnaflow highflow cat for Golf, Jetta 4 and New Beetle (for std 2.5 inch Race TDI Downpipe with Magnaflow highflow cat for Golf, Jetta 4 and New Beetle (for std clamping sleeve) 251.232...

Tuesday, October 09, 2001 - 25 Posts by 1 People

I put the homemade 3 inch pipe on my laser last nite and the results were quite interesting...turbo inch coupler and 3 to 2 inch coupler to get them to fit in there...also part of the pvc pipe inch rubber coupler...i also picked up some hose fittings and a 1 inch big pipe fitting for the BOV...