|
Tuesday, May 19, 2009 - 3 Posts by 3 People
@ 5-5-5-18 (CR2), (360ish mhz FSB) with some decent bandwidth. However, with a dram:fsb ratio of 16:10
I could tackle this by raising the fsb, and since it seemed to eat itself if it pushed it past 400mhz
Control: PCI-E OverVoltage Control: FSB OverVoltage Control: (G)MCH OverVoltage...
|
|
Saturday, March 29, 2003 - 7 Posts by 4 People
Switch to control the FSB range. That is, you can no longer select 100/133/166MHz, but only 100/Other
, but very few who understood basic stuff like what the FSB is. And I don't have one here right now
% overvoltage (1.89V). I shudder to think what +20% would have achieved ...
Gigabyte also failed
|
|
Sunday, December 23, 2007 - 3 Posts
Quality RAM OCZ
1150 MHz DDR2--PC1150.)
FSB OverVoltage control is at +0.10V; G(MCH) OverVoltage...
. I've been able to get the FSB up to 385 MHz x 9
= 3.465 GHz. But at 390 MHz the FSB eventually causes
(I have 4 Gig of high quality RAM OCZ
1150 MHz DDR2--PC1150.)
FSB OverVoltage control is at +0.10V
|
|
Thursday, October 22, 2009 - 10 Posts by 5 People
OverVoltage Control
FSB OverVoltage Control
(G)MCH OverVoltage Control
...
safely and get the clocks stable?
Voltage settings my board has.
DDR2 OverVoltage Control
PCI-E
with the following Voltages:
DDR2 OverVoltage Control : +.30v
FSB OverVoltage Control...
|
|
Wednesday, May 16, 2007 - 8 Posts by 3 People
Normal,+0.1,+0.2]
FSB OverVoltage Control [Normal, +0.1]
CPU Voltage Control [1.325V - 1.45...
OverVoltage Control [+0.1V, +0.2, +0.3]
PCI-E OverVoltage Control [Normal,+0.1]
(G)MCH OverVoltage...
I can't overclock pass 2.5ghz. I tried to follow the guide to get 3.47Ghz and tried 3.0ghz and can't get anything above 2...
|
|
Monday, October 26, 2009 - 10 Posts by 2 People
overVoltage is +0.1v
ddr2 overvolt is +0.2v
1.38125v
mobo is p35 ds3l and my temps are low 27-30 low
-E OverVoltage Control: FSB OverVoltage Control: (G)MCH OverVoltage Control...
:
System Voltage Control:
DDR2 OverVoltage Control: +0.2V
PCI-E OverVoltage Control:normal...
|
|
Friday, April 24, 2009 - 6 Posts by 3 People
To +0.3V.
I also tried changing the FSB OverVoltage Control and (G)Mch OverVoltage Control...
with a GA-P35C-DS3R. I upgraded the BIOS to F12E and changed the BIOS to 5-5-5-15 and DDR2 overvoltage control...
OverVoltage Control [+0.2V] PCI-E OverVoltage Control [+0.1V] FSB OverVoltage ...
|
|
Monday, September 08, 2003 - 6 Posts by 4 People
control: +0.1v
VCore Overvoltage control: +10%
CPU multiplier: 11x
Voltage: 1.80v
This ran Prime for...
Hey everyone,
Here's my query. I was running my PC at the following settings:
VDIMM Overvoltage
running the voltage at 1.75v and a 10% vcore overvoltage. I tried to increase multiplier to 11.5
|
|
Thursday, June 11, 2009 - 20 Posts by 4 People
At 9x)
FSB 465
PCI-E Freq: 100
SPD: 2.00
Memory Freq: 930Mhz
DDR2 voltage: +0.3v (2.2v)
FSB overvoltage...
control: +0.3v (highest it will go)
G (MCH) Voltage: +0.3v (highest it will go)
Hope you can help
reading, any 965 mobo is a little goofy with the supposed FSB strap. Where I have control over
|
|
Friday, July 10, 2009 - 12 Posts
=150
on default of 100
****VOLTAGES****
VTT Overvoltage
This item allows you to select the FSB Voltage
Right now it's on default of 3.
FSB to NorthBridge Latch
This item allows you to select FSB
voltage, but only deals with cpu overvoltage. Since I don't know what the base CPU voltage value
|
)