|
Hello all friends. I want to use Delphi to create a program that controls the fan speed of my computer and monitors the temperature.
What API calls are involved in doing that?
Are there any good code samples that you can share?
Started by Tobassum Munir on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
} Writeln('CPU FAN Info'); Writeln(' '); WMIServicesYou can use WMI to gain access to the fan speed....
For example, the CPU cooling fan.
WMI class represents the properties of a fan device in the computer system.
|
|
Hello everybody
Cannot install CentOS 6.2
Getting Kernel Panic not syncing: fatal exception in interrupt
Tried following steps:
1. changed RAM modules
2. changed HDD
3. changed keyboard, mouse
4. played with BIOS params
but nothing happened...
I've attached...
Answer Snippets (Read the full thread at centos):
It was CPU problems, changed.
Problem has been solved.
Thanks everybody.
Is the error happening on the installer boot or with the installed system? If the installer for consistent panics.
Quality image.
|
|
Hello everybody
Cannot install CentOS 6.2
Getting Kernel Panic not syncing: fatal exception in interrupt
Tried following steps:
1. changed RAM modules
2. changed HDD
3. changed keyboard, mouse
4. played with BIOS params
but nothing happened...
I've attached...
Answer Snippets (Read the full thread at centos):
It was CPU problems, changed.
Problem has been solved.
Thanks everybody.
Is the error happening on the installer boot or with the installed system? If the installer for consistent panics.
Quality image.
|
Ask your Facebook Friends
|
Hello everybody
Cannot install CentOS 6.2
Getting Kernel Panic not syncing: fatal exception in interrupt
Tried following steps:
1. changed RAM modules
2. changed HDD
3. changed keyboard, mouse
4. played with BIOS params
but nothing happened...
I've attached...
Answer Snippets (Read the full thread at centos):
Is the error happening on the installer boot or with the installed system? If the installer.
Quality image.
|
|
Hi
The CPU on the Gateway ML3108b is a Sempron 3400+. I tried to upgrade it during the weekend and this is the result:
1- With the AMD Turion MK36 the laptop turn ON, the fan spins but the screen stays OFF.
2- With the AMD Turion X2 TL50 the laptop turns...
Started by Nicadraus on
, 5 posts
by 1 people.
Answer Snippets (Read the full thread at notebookforums):
Question....
With the Turion TL50 I'm still getting the following message: "FATAL ERROR !!! Please change CPU!!!"
Does, and as naton discovered, the message 'FATAL ERROR !!! Please change CPU!!!' comes on screen ...
|
|
Heb nu mijn fx6100 altijd op 4,3Ghz lopen (200x21,5), nooit een BSOD gehad maar toch geeft prime95 altijd errors weer op een enkele core of een paar cores na een paar minuten. Vcore staat in BIOS op 1.3875V maar volgens HWMonitor komt hij nooit hoger ...
Started by rsner17 on
, 23 posts
by 8 people.
Answer Snippets (Read the full thread at hardware):
Bij intel....
Die errors houden gewoon in dat je cpu uiteindelijk niet waardoor het lager uitkomt.
Weer hardware failure, dan zegt die altijd iets van fatal error rounding was 0,5 expected 0,4Dat gebeurde bij mijn overclock ook.
|
|
On Sun, 3 Feb 2008 01:08:53 -0900, Dallas Hansen <commercial_d@hotmail.com> wrote:
I'm running Debian Etch 4.0r2 on my ThinkPad T30, 512mb ram. Noticing it felt hot under light-to-moderate CPU loads, I installed the Gnome Hardware Sensors Monitor...
Started by Dallas Hansen on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at omgili):
The CPU fan with compressed air, which I will do, but is there any
software-related solution:
I added the "options" line to /etc/modprobe.conf but was getting error messages at boot (thinkpad-acpi
From: trish@thefrasers.org....
|
|
Has anyone seen this error before?
My system hung, so I used C-A-D, and I got the following:
HoTFix: HotFix not allowed during shutdown
08869090
I've never seen a HotFix error message before. What does it
mean?
Since then, within the last day, I'...
Started by tholen@antispam.ham on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at omgili):
I had fatal CHKDSK....
The PSU is the problem most of the time, much more often that
Harddrive, CPU or anything else.
--
Trevor Hemsley, Brighton, UK
Trevor dot Hemsley at ntlworld dot,
Exactly .
Like just HPFS has this error msg.
|
|
My computer is notoriously unstable. It blue screens all the time. I'm running Windows 7. Here's what's in the box:
Intel Core i7 920 (Stock cooler, not overclocked) Gigabyte EX58-UD3R motherboard 6GB (3x2GB) OCZ Gold memory (set to 1333MHz, it has problems...
Started by Mike Pateras on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at superuser):
As for temperature - the lower the temperature, the slower the fan speed - your CPU is very cool likely a problem with the motherboard or even CPU, however, this can be very hard to diagnose.
|
|
On Wed, 21 May 2008 13:45:19 +0200, Santi Saez <santi@hostalia.com
Dear Srs,
I need to get the CPU temperature in a Supermicro X6DH8-XG2
motherboard, this is the link for key features:
http://www.supermicro.com/products/motherboard/Xeon800/...
Started by Santi Saez on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at omgili):
# ipmitool sensor
CPU | 78.000 | 80.000
CPU ....
Thermal information information via ACPI in
this motherboard? I get this error when running "acpi, prod_id: 0x0004, dev_id: 0x22)
And assuming you get all of that working....
|
