|
Well, I needed to spend the tax repate on something, so I bought a 2nd hand Graphtec Craft Robo C2200-200 off that auction site.
If anyone has not come across these before, they are a domestic version of the vinyl cutters signmakers use to cut out their...
Started by noiseboy72 on
, 6 posts
by 4 people.
Answer Snippets (Read the full thread at rmweb):
That you are cutting?
From what I've heard, these kinds of craft cutters will only cut quite thin.
|
|
I'm looking for an economical vinyl cutter suited to tasks common in the hobby such as:
Custom cut covering pieces Vinyl graphics Paint masks Paper/cardstock template making for airbrushing
So what is economical? Well, we buy a lot of expensive stuff ...
Started by racerxky on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at rcgroups):
Basically the scrapbooking crowd thinks 'vinyl cutter' is a dirty word....
They also make the Craft ROBO (also sold as the Silhouette SD these products to the craft market.
This is a craft cutter made by Graphtec America.
|
|
There aren't a lot of kits of USCG subjects around (the only plastic ones I know of are the Glencoe lifeboat, Lindberg 95' Cape-class, Revell's Campbell and Eastwind, and the Testors/Hawk 1/600 Secretary-class cutter). But I thought a CASF thread might...
Started by Timmy C on
, 20 posts
by 9 people.
Answer Snippets (Read the full thread at shipmodels):
I thought that the gray paint scheme was interesting and a rare .
To the smaller riverine craft, etc.
|
Ask your Facebook Friends
|
I have had this cutter for 2 weeks, read instructions, searched forums, and still I can't get it to cut. It goes through the motions like it is cutting, but there is nothing there. Graphtec isn't returning my calls. Any advice?
Started by Tuesday on
, 14 posts
by 5 people.
Answer Snippets (Read the full thread at t-shirtforums):
I bought a Graphtec Craft Robo...I like the cutter but they don't ....
I know sounds dumb but that would be first on my too, not now!! I am sure glad I waited to decide on the software .
Is there actually a blade in the cutter housing.
|
|
Are you like me where you can be using a tool or stamp, or embellies one moment and the next it disappears into thin air never to be found again? No trace of it?
I've lost my bone folder, heat mat and a clear stamp from my craft table.I was using them...
Answer Snippets (Read the full thread at twopeasinabucket):
If I got back all the cutter bee scissors the triangle took I could go into the used Stewart circle cutter disappeared....
As well, however I have found at least one of the culprits! I have an ott light, now how can you lose and scissors.
|
|
Http://redsgts.shutterfly.com/...usi/5
I'd been looking for a way to refinish the center covers on my wheels for a long time but no one could figure out what the right silver color was. After throwing one cover (sloppy alignment guy) and finally getting...
Started by Red on
, 6 posts
by 4 people.
Answer Snippets (Read the full thread at club4ag):
Misused a "fabric paint" that I've worked with before, sold in small bottles in craft stores.
|
|
Calling all Crafty GONers!
What helpful tips and ideas have you discovered about how to organize your craft and/or sewing supplies?
What area(s) of your home have you chosen for that purpose? Why did you choose that particular area?
What types of storage...
Started by Used2BMessy on
, 7 posts
by 5 people.
Answer Snippets (Read the full thread at getorganizednow):
How do you manage lighting? Do you limit to working in natural light? While I remember atop washer/dryer, counter,....
That looks like MS craft room Darlene a giant mess...
Like the clear bins because I can see what the contents are .
|
|
Hi, I am making my own wedding invitations. I love the cheque book style invitations but not sure how to get the look I have seen on the Internet. Basically they have somehow marked the card to it bends easily. How do I do that? Also they have perforated...
Started by Sarah_P on
, 10 posts
by 5 people.
Answer Snippets (Read the full thread at craftsforum):
I hold paper craft classes and have done sessions with brides in the past helping them, aunties, sisters, cousins, friends all helping....
I would have thought that the tools you need are a scoring board and a cutter that offers of materials.
|
|
This DIY is to convert some convertible/coupe rear lights from non-check control to check control. (Also the process would suit saloon/touring).
The symtoms are that you replace your rear lights and get a Tail Light Fail warning even when the bulbs are...
Started by Joylove on
, 8 posts
by 5 people.
Answer Snippets (Read the full thread at bimmerforums):
Once on while the light switch....
Using a craft knife, I shaved away the plastic tabs holding a craft knife, I shaved away the plastic tabs holding them in and then carefully slid them off.
The wiring, then proceeded one side at a time.
|
|
01-30-2012 10:02 AM Hi,
Thanks everyone for the help yesterday on the Diva stand. Appreciated. Was curious to see what lights you all would pair with the Diva to create a versatile kit to be used primarily in studio interviews and some run-n-gun documentary...
Started by traviswears on
, 9 posts
by 5 people.
Answer Snippets (Read the full thread at dvxuser):
Everyone should learn to light with just one source, & only then consider adding occasionally requires....
As someone who wants to continue to learn their craft, thank you for sharing your with just the other.
Such a light isn't needed.
|
