|
My Skyhawk has a 3.8L. Once it warms up the oil pressure drop to almost zero on the guage. I even had to by pass the pressure switch because the fuel pump kept cutting out while sitting at a red light for too long.
There's a couple of kits you can get...
Started by Monzadude on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at H-Body):
But I said it in a LOT less words, LOL
J/K Bryan
fyrftr422@hotmail.com
01 Pontiac Grand Prix GT
99.
It was still low but I never felt that it was going to cut out on me like it did numerous times previously.
|
|
OPEN FOR BUSINESS!
I am offering 1 car/ticket, DLC painted cars, 10 paints, 10 horns or 2 sets of gear for the 0/0/0 cars I'm looking for. Donations happily accepted!
Except for the Unicorn cars listed below, I am looking for 0/0/0 cars only! Please note...
Started by tadlock on
, 20 posts
by 5 people.
Answer Snippets (Read the full thread at gtplanet):
Completed Car/Ticket Trading Schedule (dates for Toyota PRIUS G Touring Selection (J) '03 (Black) (sent)
2/15: Suzuki GSX-R/4 Concept '01 (GSX-R/4 Yellow: VW Lupo GTI Cup Car (....
Trades have been cut from OP and pasted as follows below.
|
|
Hi
This my first time on this part of the forum. I have been an AACA member for two years now. I joined when I first acquired the Dixie. The restoration is progressing well with much of the chassis work and suspension completed. The engine total rebuild...
Started by oldcar on
, 25 posts
by 7 people.
Answer Snippets (Read the full thread at aaca):
19 inch wheels are standard....
(oldcar) These are two two Dixie Flyer(Herschell Spillman) engines for you .
Bernie J.
Hi Stude8
The AACA Library staff have been a huge help supplying a mountain of printed between 50 and 60 years .
Bernie J.
|
Ask your Facebook Friends
|
FYI For A DIY 1.6ZM Turbo Kit: Part 1 & 2 The following is a cut and paste I pulled form a PM question on what would be needed after buying one of my DIY exhaust header flanges to build a DIY low boost turbo kit for the 1.6 ZM Proetege. It can all be ...
Started by biknman on
, 15 posts
by 9 people.
Answer Snippets (Read the full thread at mazdas247):
Later, 4 wedges wre cut from each corner and 45 degree triangles were added to help match the tube Diamond and Corners
You need to cut....
A drill press and hole saw are used to cut the holes.
Plates using the gaskets as tracing patterns.
Related shopping results:
|
|
This thread will ultimately cover any of the Word Bearers novels, but for the moment covers just the three books done by Anthony Reynolds. Like Storm of Iron, they mostly fit into a 'liked better the first time around'. For me, Chaos Space Marines are...
Started by NecronLord on
, 9 posts
by 3 people.
Answer Snippets (Read the full thread at stardestroyer):
Nevertheless, to launch an orbital.
And if your hands are cut off, still you do not flee, you attack the enemy with any weapon that you have, the Vigilance was utterly cut off from the outside world.
|
|
One of the 'projects' I have on the backburner as I'm pushing towards some of the more recent and longer-running series (like the HH) is to 're do' some of my older analysis, including the Ghosts, Cain, and stuff like that. Storm of Iron was included ...
Started by NecronLord on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at stardestroyer):
There was a serrated, spiral groove....
"Facility staff do not have access.
: : Forrix mounted the dais and saw that they had cut it close, a few more minutes and Tor Christo would the facility when they realised their air supply was cut off."
..
|
|
On Tue, 13 Jan 2009 16:34:09 -0600, !Jones' Sock Puppet <hi@there.org
Actually, I kinda *like* men in tight, black panties... but, my
question has always been: How do you wear that stuff in public and
keep a straight face?
I recall when a decent...
Started by !Jones' Sock Puppet on
, 95 posts
by 36 people.
Answer Snippets (Read the full thread at omgili):
I had cut legs ....
I cut the sleeves off and made a couple of ear
covers with one sleeve and a balaclava sort, but wouldn't fit
me.
Bicycle cost a day's wages and you could ride
| the damn thing in cut-offs, a T-shirt, and sneakers.
|
|
On Tue, 13 Jan 2009 16:34:09 -0600, !Jones' Sock Puppet <hi@there.org
Actually, I kinda *like* men in tight, black panties... but, my
question has always been: How do you wear that stuff in public and
keep a straight face?
I recall when a decent...
Started by !Jones' Sock Puppet on
, 93 posts
by 35 people.
Answer Snippets (Read the full thread at omgili):
I had cut legs ....
I cut the sleeves off and made a couple of ear
covers with one sleeve and a balaclava sort, but wouldn't fit
me.
Bicycle cost a day's wages and you could ride
| the damn thing in cut-offs, a T-shirt, and sneakers.
|
|
On Tue, 13 Jan 2009 16:34:09 -0600, !Jones' Sock Puppet <hi@there.org
Actually, I kinda *like* men in tight, black panties... but, my
question has always been: How do you wear that stuff in public and
keep a straight face?
I recall when a decent...
Started by !Jones' Sock Puppet on
, 106 posts
by 40 people.
Answer Snippets (Read the full thread at omgili):
I had cut legs....
I cut the sleeves fit
me.
More
polyester than cotton.
I had a cotton polyester turtleneck.
If you were
| *really* high-tech, you had a Bendix have said t-shirt .
The damn thing in cut-offs, a T-shirt, and sneakers.
|
|
On Tue, 13 Jan 2009 16:34:09 -0600, !Jones' Sock Puppet <hi@there.org
Actually, I kinda *like* men in tight, black panties... but, my
question has always been: How do you wear that stuff in public and
keep a straight face?
I recall when a decent...
Started by !Jones' Sock Puppet on
, 106 posts
by 39 people.
Answer Snippets (Read the full thread at omgili):
I cut....
More
polyester than cotton.
You can always.
Bicycle cost a day's wages and you could ride
| the damn thing in cut-offs, a T-shirt, and sneakers wages and you could ride
| the damn thing in cut-offs, a T-shirt, and sneakers.
|
