|
Does any one have a DIY or the actualy directions of installing ground control sleeves. I already have an idea of what i need to do, but I want to be 100% sure I'm doing everything correctly. Thanks.
And yes I've searched all over this site and even emailed...
Started by R18Civic on
, 9 posts
by 6 people.
Answer Snippets (Read the full thread at 8thcivic):
I was also wondering the same thing and searched too BUMP! Is there anyone that has these on there car that still has the installation manual or directons?? i have them real easy disassemble the front shocks completely, there will be a metal cap, you ... .
|
|
Hey guys, this forum is amazing! this is my 3rd post and everyone is so great at replying.
I''m a diy kinda guy and i have made a press (the 4 color one station...) and I don't think that the press is gonna cut it.
what are the other options for multi...
Started by kwat on
, 12 posts
by 5 people.
Answer Snippets (Read the full thread at t-shirtforums):
Here is a 6 STATION DESKTOP LINE TABLE PLAN BY SANOSHIRT I have built a diy press ....
Here is a DIY of mine which I tried, or how to DIY one, should also give a boost.
Screens the clamp system of equiprint may be the only way to go .
|
|
Guys this is my first thread in your respectful forum,
I own an E39 BMW 530i 2000,
I am going through changing a (Adjuster unit) part no. 11617544805
please could you provide me with DIY for the above part.
Started by zinkawe on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at bimmerfest):
This is a 15 minute....
I could provide the DIY link but you would benefit and the answer is there.
That's your DISA valve.
Simply do an advanced search under E39 for DIY+DISAWelcome to the 'Fest.
And it provides step by step directions.
|
Ask your Facebook Friends
|
So I followed the directions on here to making a DIY CO2 Diffuser/Reactor not sure what you would call it. It is the inline version that you make out of PVC piping and fittings. Well upon completion I let it sit for two days. When I finally hooked it ...
Started by Justindew on
, 14 posts
by 9 people.
Answer Snippets (Read the full thread at plantedtank):
Last couple of DIY CO2 reactors I just ran water through them outside for a few minutes.
An hour.
|
|
DIY: Converting OBDII to OBDI using a Boomslang conversion harness
Applicable Years: 92-00 Honda Civic, 90-01 Acura Integra
Difficulty: 1 out of 5
Estimated Time: 30mins
Converting to OBDI with the Boomslang harness is super easy as it’s a plug-n-play...
Started by Jay Jay on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at clubcivic):
|
|
So, I've tried reading a lot of the older threads about tile saws, but most I find are older, so thought I'd check more recent opinion. Generally though it seems the 300 dollar range tile saws are you get what you pay for. I was considering a tabletop...
Started by vorkerman on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at johnbridge):
One thing I will say is that the directions for assembly make ikea look like god.
Great like butter.
Great for DIY.
I bought one of their rental saws (MK) for $250, and they threw in a new blade .
|
|
Does anyone have directions to do a DIY oil service and maintence on a 2002 x5 4.6is
I have purchased and K-N air and oil filter
NGK spark plugs also.
I want to get oil next but not sure what to get.
Also not sure how to replace oil filter.
Photos would...
Started by zjaber on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at xoutpost):
ECS Tuning basic diy
BMW TIS.
HERE is a generic DIY on changing the oil in a v8 BMW.
For your 4.6is.
|
|
DIY "KNG" Diffuser Blades Write Up As you know I have had a set of diffuser blades tailored to a Gen 2 and it seems they do fit a Gen 1. The cost of this setup is 100 shipped for 4 blades and 2 8 inch flat stock aluminum braces. For a 6 blade set it is...
Started by KNG SNKE on
, 30 posts
by 9 people.
Answer Snippets (Read the full thread at viperclub):
Last edited by KNG SNKE; 03-23-2011....
Re: DIY "KNG" Diffuser Blades Write Up Step.
Last edited by KNG SNKE; 03-23-2011 at 03:35 PM.
Make the blades.
Re: DIY "KNG" Diffuser Blades Write Up Step 8
Measure the distance of the holes you made.
|
|
Bout to do little make over on my garage ( 360 sq ft ). I got all the storage sorted out, paint scheme and paint purchased, now the floors.
Been thinking about attempting the DIY Epoxy floor kits that are sold at Lowes or Sherwin Williams. I'm aware preparation...
Started by AtotheJ on
, 20 posts
by 13 people.
Answer Snippets (Read the full thread at camaro5):
As said, take your time and....
CLEAN floor is very important.
It sets quick but dries really and follow directions.
It's easy, but you HAVE TO FOLLOW THE DIRECTIONS.
On the box is BS.
|
|
Hey All. Here's a neat little project we did over the weekend on Abandonhope16's LGT.
It's a DIY Open Induction Cover similar to the one maufactured by Blitz (see reviews section) but made for under $20 .
It dramatically increased the BOV sound and gives...
Answer Snippets (Read the full thread at legacygt):
Is not fixed either, it has give in all directions that act as a "suspension" for the filter assembly.
|
