|
If the idle isnt hanging when revved (lean) or the falling below idle after revving before returning to idle (rich) then you're close with the pilot.
Did you notice the glow with the pilots at 3 turns? How many miles on the bike?
Sent from my DROID X2...
Started by D-CON on
, 9 posts
by 3 people.
Answer Snippets (Read the full thread at zxforums):
I'm a DIY kinda guy and have to ask a lot.
I was at the bottom of spec on 4 intake valves Motorcycle.com Free App You give me way too much credit lol .
Clearances? We're due for inspection every 7,500mi.
|
|
NOTE: Please refrain from posting comments, if you have something you would like to add to the FAQ please PM me. This thread is a constant work in progress that I still update whenever possible. Feel free to PM with any link or info you think should be...
Started by jrcook320 on
, 12 posts
by 3 people.
Answer Snippets (Read the full thread at bimmerforums):
Coil over diy
Coil Overs
Spring Rates
Coil Over Spring Rate Selection compound:
Front Control....
Lines
-Down pipe/ 2.5"-3" exhaust
-Charge pipes/pipe couplers
-Intercooler
-Blow off /bypass valve mentioned, but it costs thousands.
|
|
So first things first, I would like to thank members of previous threads for making cooling and cooling part DIYs in the past. However, most of them were complete but were missing a few parts of the process or detailed steps. That led me to have to search...
Started by bimmerfan08 on
, 10 posts
by 7 people.
Answer Snippets (Read the full thread at m3forum):
This is seriously what I spent hours searching inspection, and no one bothered....
However, if my water pump is tanked, I'll be following your DIY.
inspection, and no one bothered to clean the old, splattered coolant off of everything.
|
Ask your Facebook Friends
|
This is the clean out. I ended up cleaning out the old threads with a small wire wheel and I was able to thread in the new cap just to gain the use of the kitchen sink with a minor drip from the cracked pipe as opposed to not using it for a few days.
...
Started by oldhouseguy on
, 12 posts
by 6 people.
Answer Snippets (Read the full thread at diychatroom):
I always thought fernco couplings met code for drainage pipes in a home inspection.
Times on older houses with iron pipe.
|
|
Ok guys this is what is needed & how i did it. (NO LEAKS) Hope this makes any sense.
Tools needed: metric torx socket set metric inverted socket set 27mm socket air impact gun harmonic balancer puller kit (rent @auto zone) front engine support ( rent ...
Started by 07841-tb on
, 14 posts
by 10 people.
Answer Snippets (Read the full thread at bimmerfest):
I recently had to replace pipe? On behalf of everyone, thank you very much for posting this! Even if some people don't do of recall with this coolant ....
Apparently there is and should be some kind of recall with this coolant pipe.
|
|
On Mon, 29 Dec 2008 11:30:10 -0800 (PST), DerbyDad03 <teamarrows@eznet.net
I'm wondering what it would take to replace the section of sewer pipe
from my house to the right of way. We have very sandy soil and no
trees in the front yard to be concerned...
Started by DerbyDad03 on
, 30 posts
by 18 people.
Answer Snippets (Read the full thread at omgili):
Laid the sc 40
pipe in and the....
We had new sewers
come.
Sewer pipes are usually pretty deep, though man there told me about
the drop on the pipe and where to put the cleanouts.
Lt;heybub@NOSPAMgmail.com
You can probably do it.
|
|
ONLINE TIS
DIY guides for pretty much everything on the car
Part 1: What you should do to keep the car running as cheaply as possible in the long term. AKA maintenance requirements.
First, an explanation of the service interval counter on the e46 M3: ...
Started by Obioban on
, 10 posts
by 9 people.
Answer Snippets (Read the full thread at m3forum):
Zionsville Radiator Water Pump Thermostat DIY:
http://www.m3forum.net/m3forum/showthread.php?t=225208
DIY key programming (for when you get a new key):
http://www.m3forum.net/m3forum/showthread.php?t it will be going on my inspection....
|
|
Our house was built in 2004 with a garden tap fed by an apparently unsleeved copper pipe through the brick wall.
I am fitting a new garden tap in a different place. It is a purpose designed tap with an attached 300mm length of 15mm copper pipe.
Should...
Started by Avoriaz on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at moneysavingexpert):
Drill a hole to accept a ....
Plumbing feeds through walls should always be sheathed in a protective outer .
Maybe I will paint the pipe with a metal primer to give the water in the supply pipe.
I didn't see much of a risk.
Thanks for that.
|
|
Hey guys blew out my VNT15 and i have been searching for a thread that lists things to look over after turbo failure. having a hard time getting any real results. not sure if im overlooking a thread or if there isnt one and everyone just gets by. either...
Started by 1.9 TDI Awd on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at 166):
Replacing the upper boost pipe plastic with a long elbo 2.5" 90, 45* 2/5 alum pipe....
Manifold all the way back to the turbo.
Haha glad you mentioned side.
Be since i had mine off for inspection/sealreplacement/steel hybrid install.
|
|
Hey guys blew out my VNT15 and i have been searching for a thread that lists things to look over after turbo failure. having a hard time getting any real results. not sure if im overlooking a thread or if there isnt one and everyone just gets by. either...
Started by 1.9 TDI Awd on
, 13 posts
by 6 people.
Answer Snippets (Read the full thread at tdiclub):
Replacing the upper boost pipe plastic with a long elbo 2.5" 90, 45* 2/5 alum pipe....
Manifold all the way back to the turbo.
Haha glad you mentioned side.
Be since i had mine off for inspection/sealreplacement/steel hybrid install.
|
