|
I have a ESR750H SLA which I want make a LI-ION battery upgrade on.
I have noticed that Goped sells a kit for more than USD1200. Buying such an upgrade would mean that I would need to sell a kidney and if I am at the hospital then I cannot use my Goped...
Started by Christianelling on
, 5 posts
by 2 people.
Answer Snippets (Read the full thread at gopednation):
Detail.bok?category=DIY+BATTER Y+PACK+KITS
How does it look in your eyes?
Thanks in advance.
|
|
Hi All, I want to diy a 300B amp but have trouble reading the many schematics available over the internet. I know that kits are available but all components comes with the kit which means if I want better components, I have to buy seperately. I was told...
Started by Me2U on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at xtremeplace):
Means so if u have trouble reading or understanding schematics, then u will need a lot of luck.
|
|
Last week i post a diy volt stabilizer was banned due to the forum rules
Started by b>Cwx7978589 on
, 148 posts
by 41 people.
Answer Snippets (Read the full thread at mycarforum):
Any recommendation for DIY grounding?
- good quality grounding kits
- instruction on DIY Bro recommendation for DIY grounding?
- good quality grounding kits
- instruction on DIY
Wires quality grounding....
As well.
|
Ask your Facebook Friends
|
Originally Posted by andrew spiel Hi everyone! I am a first timer to the forum. I am in need of advice on how to remove the 2 transmission mounts ASAP. The others were replaced twice previously by the dealer and they charged and arm and a leg. I had a...
Started by Gregory Bender on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at odyclub):
Replace it with the new one don't need to install the through bolt yet and save for the last and the through bolt as you can follow....
Just keep on unscrew it until you can pull it out with you hand; some time you need to ply.
The through bolt.
|
|
Originally Posted by andrew spiel Hi everyone! I am a first timer to the forum. I am in need of advice on how to remove the 2 transmission mounts ASAP. The others were replaced twice previously by the dealer and they charged and arm and a leg. I had a...
Started by Gregory Bender on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at odyclub):
To the front one as you can follow instruction....
Keep on unscrew it until you can pull it out with you hand; some time you need to ply it a little it with the new one don't need to install the through bolt yet and save for the last.
|
|
I'm trying to document putting one of these together, since it's not in the instructions.
First, get one bicycle cable, one thick trigger support, one thin trigger support, and one finger. Here's the cable and thick part:
IMG_0170.JPG (142.58 KiB) Viewed...
Started by rob on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at diybookscanner):
Rob, thanks for the instruction.
As I build the world's first all-mechanical steam-powered computer.
|
|
Hey bud. Do you still have all the part # for the a/c kit and the directions. Getting ready to tackle this myself. Kevin
Join AveoForum to remove ads - membership is free!
Started by kefreeman35 on
, 5 posts
by 3 people.
Answer Snippets (Read the full thread at aveoforum):
I found all the parts in wrecking yard.
Does anyone have that instruction list on how to install.
For $217.
|
|
A simple wiring diagram for push start button...
i recommend using a T-tap for the 12V and ignition wire on the brown harness.
WARNING: THE S2000 PSB WON'T FIT DIRECTLY ON THE HAZARD'S LOCATION.
YOU HAVE TO MODIFY THE BUTTON A LOT.
im not gonna post the...
Started by BATANG CITY JAIL on
, 20 posts
by 10 people.
Answer Snippets (Read the full thread at 8thcivic):
Mind answering my.
Kory 06TechCivic: I like that setup much better.
Thanks batang.
This DIY to install it.
|
|
Avast DIY K2 kalk stirrer assembly and review thread :D
this is a really nice kalk stirrer,though it came without assembly or operational instructions,they are both posted on the Avast web site for download to PDF
or here they are too...
operational instructions...
Started by Willie McDaries on
, 15 posts
by 3 people.
Answer Snippets (Read the full thread at reefsanctuary):
Re: Avast DIY K2 kalk stirrer assembly and review thread :D I went ahead and mounted the stirring/forums/...tml#post657672 Re: Avast DIY K2 kalk stirrer assembly and review thread :D next LOL Willie McDaries
360g build http://www.reefsanctuary....
|
|
Okay guys, I wasnt allowed to post in the DIY section, so im going to post it here. I dont know if this even belongs in the DIY section haha. I thought it was time to contribute back to the community even though i dont own an 8th.
This info can minimize...
Started by prorcracer87 on
, 20 posts
by 14 people.
Answer Snippets (Read the full thread at 8thcivic):
Very nice write up! dam that car is hotttt & sexyyy !!!!
awesome DIY, and awesome pics with, removing the connector took me a ....
Sweet.
On the 06 models, you dont need the stalk, so the ebay kit will work without all the extra oem parts.
|
