|
I'm in the process of fitting a mk4 golf header coolant tank to my mk2 and need to swap the pins in the electrical plug for the tank (level sender). Before I damage anything is there a knack to pushing the pins out of the plastic connectors and refitting...
Started by jmsheahan on
, 13 posts
by 7 people.
Answer Snippets (Read the full thread at com):
Some times i use two pieces of solid wires which have been ground at the edjes to become sharp there will normally be a couple of small tangs on something like this which stop... .
I don't think you are going to be able to remove the pins with a screwdriver .
|
|
I have 2 problems with my golf cab that its lost the power supply to the radio and the roof switch also the buzzer doesnt sound when the lights are left on i have changed the ignition switch and also checked for continuity at both points and still i csnt...
Started by nme motorsport on
, 14 posts
by 2 people.
Answer Snippets (Read the full thread at com):
Also check your replacement ign switch actually has a pin for this wire because some ... .
Could be the barrel itself has gone unfortunatly! but first check the thin brown/red wire to the ignition switch, thats your key-in-ignition live for radio and roof .
|
|
I had an HVAC company come out and repair my compressor unit. Locked up fan motor. While they were trouble shooting it was found to have a bad breaker outside the house. They cut the wires to the breaker and wire capped them together. First question, ...
Started by DIY Dummie on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at diychatroom):
Don't need an electrical disconnect if the electrical.
And why on earth would the AC company install an electrical disconnect? If they wired the two hots together they created a dead short.
With it.
|
Ask your Facebook Friends
|
Quote: : You need a multi tester to check the wires in each box and the light box to find the source or always hot wire...then follow one of the diagrams provided in the replies here..the idea is this: the source HOT wire goes to the common conductor ...
Started by Chris E. on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at diychatroom):
Diagram....
Depending on whether the ALWAYS HOT wire is coming into a switch box or the load(light) box:
Diagram 3 is where incoming power(ALWAYS HOT WIRE) comes into the load box .
|
|
There are new ads of an ISP in our neighborhood about their new internet service through electrical sockets in our houses. The price is a bit lower than ADSL. What is this system? What is the difference from normal DSL?
Started by Mehper C. Palavuzlar on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at superuser):
The minuses are that, given our....
The pluses are it works, and the infrastructure is cheap .
It's more common in Europe than in the US.
They've been talking about it for a while: they usually call it " BPL " for Broadband over Power Lines .
No, it's real.
|
|
I'm interested, are there any sites where one could find an approximation of electrical consuption, so if one has different configurations, one could approximately calculate consumption of that configuration if it worked for example, 24/7, for a full ...
Started by ldigas on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at superuser):
Next....
The easiest thing you can do is buy a monitoring device that you can plugin between the device and the socket such as the following:
If you cannot find one, then try to find out as many specifications as possible - You really need Amps and Voltage .
|
|
I'm 21. My senior year of undergrad university is approaching quickly, and I don't know what I'm going to do when I graduate. Instead of seeing the light at the end of the tunnel, I'm bored and apathetic about graduate school or entering the workforce...
Started by Jeremy CD on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
Pick up a book by Douglas Coupland for fun reading, wade through Michele's Foucault for a conceptual challenge, or sit down with Shakespeare and work on understanding... .
To me, it sounds as if there's another problem and you're keeping yourself distracted .
|
|
Employee's Beware about This is written as a warning to all persons who are considering employment with Electrical Environmental Systems (EES). As a former employee of the company, I believe it is necessary to inform the potential employee of my experience...
, 1 posts
Answer Snippets (Read the full thread at hallway):
|
|
Hi All,
I recently graduated with a B.S. in Electrical Engineering and gained a lot of interest in embedded systems in both hardware and software. When I got out of school I got a job as an entry level Software Engineer in embedded systems. Having experience...
Started by Sean on
, 10 posts
by 10 people.
Answer Snippets (Read the full thread at stackoverflow):
As part of course we studied about Sensors, ....
Did a BE in Electrical Eng (HW + SW and Control.
For this I need to get a Masters in Electrical in order to move, but movement in the opposite direction is difficult.
Design and integration.
|
|
Hi, Guys
Total Noob at the but i have a GT-S hatch that has no electrical in the front the rear is still there (Tail,Turns lights) my question is can i get a under dash and headlight harness from any other 86. like a sr5 coupe ? Mind you i am looking ...
Started by Nevernot86 on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at club4ag):
|
