|
Hi all,
I've been getting small electrical tingles from the grill of my microphone, and I'd like to get to the bottom of it.
I've got a set-up involving one or two (the problem happens in both situations) Behringer XM1800S microphones going into an M-...
Started by Joe P on
, 27 posts
by 12 people.
Answer Snippets (Read the full thread at blue-room):
Butcher one.
These are used to prevent static build up in the body and frying electrical components.
I personally rarely use a guitar in this set-up, but the other day a friend of mine did, and lo.
|
|
This thread is to become a forum where practising Electrical Engineers and the aspiring ones can interact. I fall under the aspiring group so I hope for a situation where the professionals can give us, the aspiring ones, an insight as to what is expected...
Started by Fireman Jr on
, 32 posts
by 11 people.
Answer Snippets (Read the full thread at nairaland):
So this thread to the 'Ask AjanleKoko....
Most machines use on d site r PLC based.
I'm an electrical engineer as an electrical/instrumentation personel in a manufacturing coy.
Hi, Thought to open the discussions with a brief summary about myself .
|
|
My Cub is finally coming together and I am now thinking I am going to replace all the electrical stuff while it is apart... yes the old worked but it is just that -old and some of it looks like it has seen a better day. The Cub has been FULLY taken apart...
Started by code54 on
, 13 posts
by 8 people.
Answer Snippets (Read the full thread at farmallcub):
This will be easier on both your wallet and our landfills... .
- - - - - - - - Or something like .
My wife says I don't listen to her.
If the current electrical appliances (alternator, starter, coil, etc,) work an electrical problem.
My opinion.
|
Ask your Facebook Friends
|
I have a set of heated grips with the variable temp control that won't work on my FZ6 (throttle tube on the grips preinstalled and only has 1 cable hole) and I also have a set of those under the grip heaters with a off, hi, lo switch.
My question is can...
Started by badweatherbiker on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at advrider):
You should be OK, but if the wattage on the under grip heaters is significantly greater it may cause the temp control to fail so just compare the watts or amp draw for each one and if they are the same, or if the under grip heaters are less watts or amps... .
Related shopping results:
|
|
Posted Yesterday, 08:02 AM
I lost my headlight and tailight but all other gauge lighting is working, sled still runs fine? Anyone ever see this, think its a harness issue or is there something else that could have went to affect the lights only?? 1998...
Started by onebad800 on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at dootalk):
Posted.
The wiring in the handle bars rubs through or the hi beam/lo beam switch can cause a similar issue.
|
|
My girlfriend has a 99 Wrangler. Today we put in a new heater core and blower motor resistor. It now blows hot air, but the fan still only works on high. The old resistor was all rusty anyway, but what else is there to have gone wrong?
I checked the motor...
Started by marcar1993 on
, 19 posts
by 7 people.
Answer Snippets (Read the full thread at oldspower):
Lo and behold, the fan WAS working on the LO and MED positions, but I just couldn't hear it over the engine, and the squirrel cage.
To "ON" without starting it, and play with the fan switch .
|
|
I was away on holidays for a few weeks and my 407's battery went flat. Since a jump-start, the radio (Blaupunkt RD4) will now not turn on whatsoever. I do have a Dension Gateway GW300 hooked up to the loom (very similar to Peugeot's branded "USB Box")...
Started by WetDaddy on
, 15 posts
by 5 people.
Answer Snippets (Read the full thread at boards):
The solution.
Including the loom that it came with and, lo-and-behold, the radio sprang to life.
|
|
Lo all, Im taking the T5 door off for the usual reason but the electrical connection wont bubde so clearly im doing it wrong and i dont want to break it.
I have removed the tiny little torque bolt in it , does it literally just pull off , no twist or ...
Started by mas on
, 8 posts
by 5 people.
Answer Snippets (Read the full thread at volvot5):
Its a twist connection, and its a dam site easier while the door is away from its fixings, twist it anti clockwise too also other thing i do is persuade it with a screwdriver on the little noggins too Sorry to hijack the thread is it easy to take a front... .
|
|
I started construction on my Lo Volt in July. I spoke with the E-pod electric motor company and discussed the use of the motor pod on the LO VOLT. This last week I went to order the E-Pod 2000 and could not place the order. The company will not return...
Started by Bruce Dow on
, 10 posts
by 6 people.
Answer Snippets (Read the full thread at glen-l):
My general construciton in under power boats - Lo Volt done in the next couple of....
I hope that is how it is done.
Building Lo-Voltage as well and moving forward.
electric motors!!! so why not a cooling jacket for a golf cart motor.
|
|
I've had a couple of electrical issues in the last couple of days and I'm hoping that it isn't a sign of something larger that's about to happen.
Tuesday morning I noticed my Driver Side reverse light wasn't working. No biggie, the car is nearly 8 years...
Started by GRNDHOG on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at elementownersclub):
Terminal or electrical type cleaner and a can of battery terminal protector
and clean and protect all.
|
