|
I have been doing a bit of night riding lately and wasn't impressed with the stock headlight, it's set up great for possum hunting but not night riding, so I wasthinking of an upgrade. I stumbled across a spare 12v H4 55/60w globe for a car and was pleasantly...
Started by berglsmerg on
, 13 posts
by 8 people.
Answer Snippets (Read the full thread at husaberg):
Except for a FE 610 how about the heat from H4? I expect it to melt some plastic crap/products/browse/h4 FE 570, when you absolutley have to roost every mutha in the room , accept a real problem if it was like 100w....
No substitues.
|
|
Well last week my truck would idle fine and now it will stall out .the only thing i can think of is my rusted gas tank is giving me too much problems.i cleaned it out but still killing the motor.i changed the fuel filters and took the carb out and cleaned...
Started by evolutioneng on
, 14 posts
by 3 people.
Answer Snippets (Read the full thread at fordification):
If its visably flooding then....
All the more reason to check agreed.
Does not mean the floats can't have problems.
New.and the floats are plastic instead of copper.
|
|
I'm wondering if a transmission with a slip yoke can be used with a two-piece driveshaft? Should I do this or will it cause something nasty to happen? 390 FE IN A BUMP/ 383 WEDGE IN A 2-DOOR C-BODY/ 351W IN A FULLSIZE MERCURY (Driver)/ 194 CHEVY 6 IN ...
Started by Nitekruizer on
, 11 posts
by 3 people.
Answer Snippets (Read the full thread at fordification):
The carrier bearings slack there or if the yoke should be almost all the way in ,say 1/8" or so for example ? 390 FE/ 2.4 DOHC CHRYSLER IN A PLASTIC BUBBLE....
And the additional vibration was absorbed by the carrier bearing rubber.
|
Ask your Facebook Friends
|
I ve had this question in my mind for quite some time now and the more I think about it, the more confused I get.
1. I cannot afford a new Fortuner (and do not think it is VFM too) and I do not think that a new Pajero SFX is worth the money. The Yeti ...
Started by n.devdath on
, 15 posts
by 11 people.
Answer Snippets (Read the full thread at team-bhp):
plastic locks break, rubber gaskets You should go for a used Fortuner if you can get a good VFM specimen.
|
|
I just purchased the best 50- used 20 gal. parts washer I could find.... Actually it is fairly clean and almost new looking. The pump internals look to be plastic (impeller). So Berrymans may not work, nor will any of the old school flammable solvents...
Started by TORKTEK on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at network54):
JMO with a plastic pedestal and impeller....
As far as the plastic pump parts go I wouldn't think they would be at risk as mineral spirits come in plastic bottles.
Evaporation doesn't seem to be an issue and I live in a very dry climate .
|
|
Has anyone used the chrome powdercoat on anything that is supposed to be chromed? I been thinking of doing a set of early merc FE baldy covers I have. I also thought of getting a set of bumpers done on one of my cars as chroming is $800 for just one bumper...
Started by GJCAT427 on
, 18 posts
by 7 people.
Answer Snippets (Read the full thread at network54):
You can "triple chrome" plastic, however quarter panels from burnout rubber.....
Is mostly vacuum metalized, as far as production parts go .
It can't be paint.
Chromed plastic parts like grilles that stand up very well over the years.
|
|
Ethanol information for Mazda vehicles
What is Ethanol?
Ethanol is a colourless liquid (alcohol) which is produced by fermentation of sugars and carbohydrate polymers and is generally manufactured from grain or sugar. Blending of ethanol in petrol has...
Started by tailland on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at mazda3club):
Does anyone know if this is also true for the 2010? Just got a new 3 and the didn't mention E10 - but that would be awesome. .
|
|
Hello Every one,
So after long hours of research in many forums including TAI , reading zillions of reviews, scanning through hundreds of blogs and a few test drives, I finally zeroed down on Honda BRIO.
I got it delivered on Monday - 30th April (One ...
Started by sudeep.roy on
, 14 posts
by 8 people.
Answer Snippets (Read the full thread at theautomotiveindia):
Unsatisfied about many things in Beat including the paint job, pickup, FE, congested back seat, ASS etc Beat is known for its build quality,good quality plastics and rubber and for the excellent fit Beat is known for its build quality....
|
|
Made a rampump?
Has anyone made a rampump on here??:rolleyes:
I have a neighbour who has put a new drain from a spring ,into my ditch ,and I wanted to put a really large tank by it and use a home made rampump to keep it filled !
I thought of solar pump...
Started by Huffy on
, 9 posts
by 7 people.
Answer Snippets (Read the full thread at farmingforum):
As I understand it the supply pipe has to be metal - plastic for intermittent use, and they have ....
And rather than sink a 2 inch plastic or metal supply pipie to the ram (It would need to be quite of fall to vertical head is critical.
|
|
My 1994 Ford Escort aka The Trusty Escort Hey guys..A week back I picked up a 1994 Ford Escort LX model. Has around 52,590 or so miles on it and is in pretty good shape all around. Couple small rust spots near chips and whatnot but overall a pretty nice...
Started by 87gtVIC on
, 20 posts
by 9 people.
Answer Snippets (Read the full thread at grandmarq):
~ David ~
My 1987 Crown Victoria.
Color is called Light Santa Fe and the car has a 1.9L engine.
|
