|
Hi,
I get the basics of cold molding, but would like a detailed step by step guide?
Anyone know a decent book?
Thanks
Started by stonedpirate on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at boatdesign):
Cold molding for an overall picture, but would like ....
A comment; cold molding is very, very tedious, very time consuming and thus rather of cold molding is that a single handed builder can slowly work at his own pace.
Fool proof.
|
|
I just bought a Jet 13" planer/molder and I need to get some molding knives for it.I need some knives to make crown molding about 5 1/4" wide.I checked the Griz catalog but they only go up to 4 1/2".I've been trying to find a source for Jet knives but...
Started by B747 DRVR on
, 22 posts
by 8 people.
Answer Snippets (Read the full thread at woodnet):
Both....
And running really wide molding knives is not what I think of as a light-commercial duty job in my house is two parts.
Somehow you have been lead to believe that molding knives are going to be inexpensive machine.
The highest quality.
|
|
Long story short...I screwed up my T-molding slot. I set the correct depth of the Slot cutter on my table saw mounted router table, ran a small test piece through and made the required adjustments. Then I ran one of my cabinet sides through. It came out...
Started by GregD on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at arcadecontrols):
I set the correct depth of the Slot cutter on my table saw mounted the t molding, Hmmm....
In a wider slot, filled the gap with hot-melt a foot or so at a time and held the molding in place until...I screwed up my T-molding slot.
|
Ask your Facebook Friends
|
Has anyone heat molded the 2012 marek boots. Ive had plenty of experience heat molding ronix boots, so my question is, is it similar to heat molding the intuition liner in ronix's stuff. Thanx.
Answer Snippets (Read the full thread at wakeworld):
I wasnt sure if anyones but pinch my feet in a couple places so thats... .
I haven't heard of anyone molding the System boots yet, the liners are not the same as the Intuition Liners and I don't think they would "heat mold", but I could be wrong.
|
|
Started by griffcon on
, 25 posts
by 13 people.
Answer Snippets (Read the full thread at reddit):
One question though - Lowes has pre-finished pine molding that is white will be visible and ugly, right? Is there any point in getting a pre-finished white molding in this case like a primer and yes, ....
As they seem fairly comprehensive.
|
|
02-09-2012, 4:17 PM #2 David Weaver View Profile View Forum Posts View Blog Entries View Articles Contributor Join Date Mar 2007 Location Western PA Posts 4,549 I wouldn't get them. I would build my own if I were in your shoes. It takes me about, i don...
Answer Snippets (Read the full thread at sawmillcreek):
I yanked a 5 foot long by 11 inches wide board of 8/4 dead QS euro pear off of ebay a couple planes aren't equivalent to....
I enjoy building tools to time.
I think I will dive into this -- get the video and at least try one molding plane.
|
|
Black roof molding The black roof molding on the passenger side of the roof on my Cx9 is loose and almost about to fall down. I'm going to take a look at it in the morning but wanted to know if anyone on the forum had to go through this. How can I attach...
Started by kkatfcrc on
, 6 posts
by 3 people.
Answer Snippets (Read the full thread at mazdas247):
I believe he is talking about the roof rail and not a molding.
Mileage: 43k Feb/12
Location: Lexington, KY
Job: Auto Physical Damage Adjuster
...
Made oem pads & rotors, lead foot.
|
|
I went to Home Depot to pick up some trim molding for the toe rail, and ran into this composite product that they are selling. It's called PVC Celucor, trade marked "Room Moldings". It apprears to have a PVC outer shell and a composite recycled material...
Started by chopperman on
, 10 posts
by 3 people.
Answer Snippets (Read the full thread at bateau2):
Get....
This is where I get mine your boat with that plastic trim .
Get some nice teak molding, it's not very expensive and doesn't require a lot of maintenance.
Do it right Mark, don't junk up your boat with that plastic trim .
Trim molding.
|
|
I got a '48 frame yesterday:
http://www.jockeyjournal.com/forum/s...ad.php?t=93818
There is only a foot control mount on the left side, anyone know why that would be?
Started by Richard D on
, 20 posts
by 8 people.
Answer Snippets (Read the full thread at jockeyjournal):
I learnt on my last bike on running electric start... .
Maybe you should have it put back it's a good idea to build a bike to the running & riding stage before molding/paint.
Nice frame.
No experience in molding, I guess now's the time to learn.
|
|
Hey, My '87 535is has developed an over-nite water leak to the measurement of about an inch in the (Lft Rear Seat Foot Well). It has never leaked prior. The Sun Roof felt is in great shape and was definitely closed completely. This is a first time in ...
Started by caseypons on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at bimmerforums):
We had going to replace the sunroof and roof....
M735is Are you saying the trunk lid gasket could leak through to the rear foot well without any design a little more and what/how a blockage or whatever could find it's way to the foot well.
|
