|
Does anyone now where i can buy hdpe|(poly pipe|) near burbank illinois....i just get the run around online..please email me jkfish34@aol.com
Started by frerter29 on
, 14 posts
by 11 people.
Answer Snippets (Read the full thread at pyrouniverse):
If your looking for tubes, then buying your own pipe MAY get you....
Www.Addyracks.com If, as the post reads, are only looking for pipe then I have not the foggiest idea.
Check out Addyracks in Joliet if you are looking for HDPE tubes.
|
|
Hello All
We are currently trying to modify the internal couplers on our piping system and one of the solutions is to increase the thickness of the couplers. This will result in a decrease of the pipe OD which will ofcourse have much more effect on the...
Answer Snippets (Read the full thread at eng-tips):
Its a corrugated HDPE pipe so we dont have for....
External couplings for HDPE are readily available.
The pipes are HDPE pipes Any reduction (or expansion) in pipe size will affect this.
I forgot to mention.
|
|
Have a customer with short ground loops and too small water supply lines to thehome.
Right now I'm taking care of the supply line to the home first.
The heat pumps are in a machine shed about 20' away from the home. There are two heat pumps each with ...
Started by DeltaT on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at hvac-talk):
Couls not operate.
Long radius and very pipe freindly.
Eric corners when running wire inside pvc conduit.
HDPE with a fusion x MPT adapter run through a electrical sweeping 90 would be my choice.
|
Ask your Facebook Friends
|
It is with great sadness that I create this thread. But, it's time to move on, so my loss could be your gain.
Anyway, it's a 1990 s13 hatch SE model. I have no idea how many miles are on the chassis, but there are about 2000 miles on the engine (and I...
Started by s13pimp on
, 7 posts
by 3 people.
Answer Snippets (Read the full thread at zilvia):
Thank you for the reply....
Anyway, I'm located in Syracuse, NY (about 5 hours North West of NYC) .
Almost like a second job at times.
Looks like a great project, was wondering where in NY you're located? Thanks! Yes, it certainly has been quite a project .
|
|
Anyone know if this acceptable/safe to use as mortars?
It is made of MDPE (Very simular to HDPE) This stuff is used is underground gas line applications. It has a pressure rating of 1,000+ PSI. With that being said, I'm not so worried about it not being...
Started by jonkelley82 on
, 16 posts
by 9 people.
Answer Snippets (Read the full thread at pyrouniverse):
The biggest detractor is that it will be even heavier than hdpe, but it won't shards that it is available in sticks? The photo in your link was coiled, and as people have mentioned with HDPE, dealing The above mentioned natural....
A whole rack.
|
|
My wife and i are considering the purchase of a lot to build a home. the lot is a subdivided parcel of a larget plat. the lot is 1.25 acres and is served with municipal water and sewer, as well as natural gas and electricity.
the lot is located just north...
Started by cobra5laddict on
, 15 posts
by 7 people.
Answer Snippets (Read the full thread at diychatroom):
If so, a contractor can easily plow or chain trench a poly line 100' long to the road (again, unless you plan to pump)
2) Find out if your municipality allows poly pipe of this? the install was completed in the past....
Poly pipe for services.
|
|
Hey guys, I'm new here. I'm planning on making some mortar racks that fit dr11 HDPE pipe for consumer shells and I'd like to get your guys' input on this. I'll be buying 50 mortars, and I'll make 10 racks. The holes on the sides are for a bolt/wingnut...
Started by gman on
, 11 posts
by 5 people.
Answer Snippets (Read the full thread at pyrouniverse):
Just pre-drill and coat the joint.
2 screws a joint? Yes, I would use 2 screws per joint - those zinc comment on durability - it will be fine with 4 screws total.
Not to put a screw through the hole.
|
|
On Fri, 28 Aug 2009 20:36:17 +0100, Stephen <invalid@invalid.org
Hello,
A relative has an outdoor tap. The walls and floors are concrete so
difficult to drill (non-sds), so whoever fitted the tap took the easy
option of drilling through the upstairs...
Started by Stephen on
, 13 posts
by 9 people.
Answer Snippets (Read the full thread at omgili):
IME non return valves do the same thing in miniature:-(
Good luck:-)
regards
--
Tim - the pipe....
That won't the
pipe.
I would replace the whole drop with black HDPE pipe.
Ksbg951h3suq5k1emtur1pk7e3imbrobbl@4ax.com...
|
|
Summary of Changes in
ASME Section IX, 2010 Edition
As published in the Welding Journal, August, 2010
Prepared by
Walter J. Sperko, P.E.
Sperko Engineering Services, Inc
Greensboro, NC 27406 USA
Changes to ASME Section IX, 2010 Edition
Walter J. Sperko...
Started by sooeey2u on
, 2 posts
by 2 people.
Answer Snippets (Read the full thread at egpet):
Visit www.cswipquestions.blogspot.com for model question and more.....
|
|
I helped some friends install an LG room AC last week and it came with a straight plastic condensate drain nipple that snaps into the sheet metal on the back of the unit at the condensate pan low point. To improve drain hose routing I'd like to replace...
Started by raylo32 on
, 9 posts
by 3 people.
Answer Snippets (Read the full thread at diychatroom):
I guess....
Http://www.homedepot.com on to it.
It is made of black plastic, I am guessing HDPE or ABS.
Another view on page 20.
Is shown in the manual on page 12, labeled Type C, 1 each, drain joint pipe and drain joint washer.
|
