|
Id like to start doing some pocket hole joinery (were just getting started in wood working). Id like to only buy once, so figured Id ask for opinions out there. Which would you buy today, the Kreg system (not sure what all I need unless I buy the kit)...
Started by Zudnik on
, 9 posts
by 9 people.
Answer Snippets (Read the full thread at woodnet):
Kreg....
The Kreg must be reset for every thickness it.
Kreg did make one drill bit is set once and will then work for every hole.
A cabinet side I had to adjust my arm around the other side for every hole, that got old.
|
|
Just a beginner to woodworking and I need a kreg jig to connect boards and whatnot... was wondering if the Kreg Jig Jr. is sufficient or if it's worth it to spend the extra money on a full Kreg Jig?
Thanks.
Started by ZeekLTK on
, 7 posts
by 6 people.
Answer Snippets (Read the full thread at woodworkingtalk):
I dont have time right now to learn m&t joints but pocket holes allow me to enjoy woodworking not to bother with pocket....
Some on here will bash pocket hole joinery but i say to hell with them.
I love it.
Get the full k4 kit.
|
|
Kreg k4 Jig Hi guys, does anyone know where I can get the kreg k4 pocket hole jig in Ontario? I am in oakville.
Also if anyone has one they want to sell let me know?
Thanks,
matt
Started by mlalande on
, 16 posts
by 11 people.
Answer Snippets (Read the full thread at canadianwoodworking):
Re: Kreg k4 Jig ....
I know in Calgary they do.
Re: Kreg k4 Jig Matt,
I think the Home Depot has now started to carry them.
If you buy them before feb28, there is a $15 ones are nuts .
Re: Kreg k4 Jig Lee valley in burlington has them.
|
Ask your Facebook Friends
|
We have a Kreg unit at work, and use it all the time in case building. It's definitely all that... We use the blue corrosion-resistant screws...
Started by Joe Dirt on
, 11 posts
by 4 people.
Answer Snippets (Read the full thread at diychatroom):
The Blue-Kote Kreg Pocket Hole Screws are Zinc plated with some additional layers Information" from Post #17 of this thread:
" Blue-Kote ™ Kreg Pocket Hole Screws feature a three layer Kreg pocket....
|
|
On Wed, 3 Dec 2008 15:02:46 -0800, "Chuck Olson" <chuckolson01@REMOVETHIScomcast.net
I saw a close-up view of the 3-hole guide in one of the videos, so I stopped
the picture in the middle of the close-up and using a scale on the screen
measured...
Started by Chuck Olson on
, 7 posts
by 6 people.
Answer Snippets (Read the full thread at omgili):
Right, and I'm sure that's the reason why Kreg never), "....
When I need two, I use;beech23pilot@yahoo.comnews:ujEZk.9716$YU2.6161@nlpi066.nbdc.sbc.com...
When I need one hole, I use the center opening.
But never cared to measure them.
|
|
Time to bite the bullet. Are the Kreg set ups a good choice? They've dropped the prices it appears, since I last looked.
Started by bobabode on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at audiokarma):
Kreg or....
I only need advanced types.
I have one of the less expensive Kreg pieces, and am very satisfied with it.
Of quality.
Related shopping results:
|
|
Hi, I thought I'd post about my pocket hole jig. It's the Kreg K4. I had never used pocket hole joinery on anything before. I recently built a mantle and used pocket hole joinery for the speed. I have read all the pros and cons of these things on this...
Started by ACP on
, 14 posts
by 9 people.
Answer Snippets (Read the full thread at woodworkingtalk):
I have read all the pros and cons of my... .
I recently built a mantle and used pocket hole joinery for the speed.
I had never used pocket hole joinery on anything before.
It's the Kreg K4.
pocket hole jig.
|
|
Hello everyone I have been lurking on this forum for awhile so thank you for all the info. I am getting prepared to start working on a end table and a night stand. I am military so it is a matter of time before I move so it is easier if I can talk furniture...
Started by sgtrunningfool on
, 19 posts
by 13 people.
Answer Snippets (Read the full thread at woodworkingtalk):
My Kreg jig in the UK cost 11 GB butcher.....
Cant remember which issue.
Kreg makes an affordable pocket hole jig that works 0311 Shop notes has a pocket hole cutter.
And effort worth? Not to mention your sanity.
|
|
Yesterday, 12:24 PM #2 Jerome Hanby View Profile View Forum Posts View Blog Entries View Articles Contributor Join Date Nov 2006 Location Trussville, AL Posts 3,303 That may not be the silliest product I've ever seen, but I could be wrong. Unless I looked...
Answer Snippets (Read the full thread at sawmillcreek):
Has the Kreg company been on the....
Kinda makes me wonder.
Lo barato sale caro.
I love my Kreg clamps and pocket hole is, that fiction has to make sense.
As well, what with the Kreg emails that led up to this unveiling.
|
|
I have a kreg jig. I use it a lot and I'm very happy with it.
Lately I have been wondering if I could make something for the drill press that would work better. But before I go about re-inventing the wheel I thought I would ask if anyone else has come...
Started by georgenoeth1 on
, 4 posts
by 3 people.
Answer Snippets (Read the full thread at woodmagazine):
George Noeth (Gadget Guy)
Wood Online forum Host.
As to the concern about the depth adjustment, perhaps I could use part of the Kreg with the stop collar on the bit.
Always pull out the kreg.
|
