|
Good infoguys.
I have great luck with the Milwaukee brand key hole saws for metal at Home Depot, cut through my rool bar tubes fairly easy. I just use penetrating oil for cutting oil, not sure of the difference.
Started by mopar346 on
, 15 posts
by 10 people.
Answer Snippets (Read the full thread at jeepforum):
If you have any paint hole saw with plenty of new motor oil to lubricate the cut, and then enlarged the holes a bit variable speed Dewalt drill with....
I forget the brand.
I used a bi-metal hole saw bit I got from Lowes.
|
|
Cheap Hole saws for cutting dash holes, extern lighting holes etc Just found this site:
UK Drills
- prices much cheaper than anything Ive seen before, and much cheaper than the high street.
Probably only good for cutting a few holes before going blunt...
Started by KevinW on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at cobraclub):
Piece Hole Saw Set: Amazon.co.uk: DIY & Tools
I cut a few 4 inch holes and the cutter still had teeth.
|
|
Does a hole saw make a hole all the way through the door? or do i have to go on the other side of the door and make another hole?
Started by Terry on
, 7 posts
by 7 people.
Answer Snippets (Read the full thread at yahoo):
Depends on how deep the....
Besides the saw tends that.
The hole saw has a pilot drill in the middle so once it goes through, so you should drill from both sides to get neater edges to the hole.
Go at it from both sides anyway.
|
Ask your Facebook Friends
|
I need to cut a 2 1/2" hole in my firewall and the steal reinforcement plate I made to support my hydroboost. I picked up a "Bi-Metal" hole saw and it cut through the firewall ok but was to dull to cut through anything by the time I got to the support...
Started by casadejohnson on
, 15 posts
by 14 people.
Answer Snippets (Read the full thread at classicbroncos):
The only thing I have seen defeat it in 2.3
Of course ... .
Ouch! Morse is a pretty common brand of hole saw.
The ones.
Just type in HSS Hole Saw.
A punch?
There are some hole saws on Amazon that look interesting.
|
|
Metal cutting hole saws I have been search and can't find the answer, I need to drill 1-1/2 holes in 1/4 thick mild steel. Can you do it with a metal cutting hole saw? What brand/type is best. I have a box of good Lenox ones but I will buy what is nessary...
Started by Mark in Burlington on
, 20 posts
by 8 people.
Answer Snippets (Read the full thread at canadianwoodworking):
Can you do it with a metal cutting hole saw? What for even simple....
I've used lenox, I need to drill 1-1/2 holes in 1/4 thick mild steel.
Fluid and a hole saw works fine in metal if it's stated for that purpose as well.
|
|
Hello,
I need to create some 3 inch diameter 3/4 inch thick "disks" out of 3/4 poplar, by using a hole saw on my drill press. I have a Ryobi 10 inch drill press, and I just bought a hole saw kit from Harbor Freight.
Any suggestions as to the best way ...
Started by LouB on
, 14 posts
by 10 people.
Answer Snippets (Read the full thread at woodnet):
And to use a piece of stock maybe 3 1/2" - 4" wide and position the hole saw off center so will for the sawdust....
You will have to take small bites and clear the chips out frequently. .
It at it slowest speed when using a hole saw.
|
|
Just borrowed a hole saw from the metal shop.
wanted to punch an extra fan hole ontop of my sonata III as the new antec 620 is going to be blocking the only exaust port.
I think the 4.5 inch saw will be too big, so Ill have to settle for the 4 inch saw...
Started by prudhomb on
, 13 posts
by 5 people.
Answer Snippets (Read the full thread at extremeoverclocking):
Its really simple
http://www.youtube.com/watch?v=7wGlW...ayer_embedded# Cool link saw to put on the 4 1/2 in ....
Its really simple for adding the hole.
Watch this video as it will give you all the info you need for adding the hole.
Related shopping results:
|
|
I've been looking into buying a hole saw set for cutting through steel plate and to notch tubing. The max thickness that I would be cutting would be about 1/4 inch. I'm looking into this set from Northern Tool. Any info on this set or if anyone can point...
Started by thebigyellowtruck on
, 15 posts
by 13 people.
Answer Snippets (Read the full thread at yesterdaystractors):
Long ago I gave up on using a drill bit in the hole ....
I'll try it next time I use a hole saw.
Once it flat spots on the ends of any hole saw teeth you might of the washer trick.
On the arbors would not stay tight.
|
|
What hole saw type Hello,
Im working on a new project in O1 and need to make a 26mm diameter hole. I have a 22mm hole saw bit, one of the yellow painted hss bits with pilot drill bit which i used for mild steel at some point but even on 3mm thick O1 i...
Started by tatsumi on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at britishblades):
Re: what hole saw type cheers mate, it might be my expectations hole saw....
Re: what hole saw type I just noticed how many times i used the word bit there lol Re: what hole, or a lot of faffing about, or both.
|
|
I'm about to install a new faucet and it appears that the size is 1 3/8. Is it acceptable to use a 1.5" hole saw for the holes, or does this cause issues? It's just a temporary install at this point (no counter tops yet).
Started by Tonglebeak on
, 6 posts
by 6 people.
Answer Snippets (Read the full thread at diychatroom):
Have you measured ....
Is it acceptable to use a 1.5" hole saw for the holes...
Is 1 3/8.
|
