|
I have a situation where I need to boot Windows Vista 64-bit from both a ICH10 and ICH8 AHCI SATA controller. Currently, it is setup to boot from the ICH10, but when I try booting with the ICH8, I get the famed Windows STOP 7B BSOD. How can I add the ...
Started by adurity on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at superuser):
It detected the change of Mass Storage controller, configured it, and began installing .
This issue for me.
|
|
I bought 2 7200.2 HDs and put them on an ASUS P5BVM-DO. I could not believe I had 2 bad HD's, so I tested them separately. Same, so I assumed it still could not be the hard drives. The chances of 2 bad ones is very low. We slowly swapped out everything...
Started by czhower on
, 7 posts
by 4 people.
Answer Snippets (Read the full thread at seagate):
From what I can see, its yet another bug.
There are a fair bit of people who have this issue on XP too.
|
|
On Mon, 09 Mar 2009 10:46:57 +0200, Alexander Motin <mav@FreeBSD.org
Hi.
It is ICH8M port, right?
There is very little part of AHCI driver takes part on this stage.
Mostly it is done by common ata_sata_phy_reset() routine. Try to comment
if...
Started by Alexander Motin on
, 23 posts
by 16 people.
Answer Snippets (Read the full thread at omgili):
Which is a different issue and seems to need a similar patch to that
applied.
issue I reported on questions that lpt0 now just
reports "device busy"?
Beech unit2minor undefined
..
|
Ask your Facebook Friends
|
On my first CentOS installation and loving it so far. Except I can't get accelerated graphics / it appears only on half screen.... I have updated the centos by using yum update command but the problem remains the same (which normally work by default on...
Answer Snippets (Read the full thread at centos):
To overcome from this issue
Pressed TAB button to edit boot menu
vmlinz.init = vmlinz,init
I has modified.
|
|
On Mon, 16 Feb 2009 16:25:39 +0200, Giorgos Keramidas <keramida@ceid.upatras.gr
I just rebuild my kernel after flipping the switch to usb2 in my kernel
config file:
diff -r 657f71f9e39c -r 82c23c5ef94e sys/i386/conf/KOBE
--- a/sys/i386/conf...
Started by Giorgos Keramidas on
, 14 posts
by 7 people.
Answer Snippets (Read the full thread at omgili):
Microsoft
usbus4 is attached as:
usbus4: <Intel 82801H (ICH8) USB controller USB-Busbus4: 12Mbps Full.
|
|
On Mon, 16 Feb 2009 21:29:38 +0100, Hans Petter Selasky <hselasky@freebsd.org
<hselasky@freebsd.org
Hi,
What is "usbconfig" saying about your mouse?
How is your mouse connected to the PC? Directly or through a USB HUB?
--HPS
______________...
Started by Hans Petter Selasky on
, 18 posts
by 10 people.
Answer Snippets (Read the full thread at omgili):
Either a timing issue, i.e.
USB part worked almost identical, it's the CAM part that didn't happen in the
second case to interpret this .
Intel 82801H (ICH8) USB controller USB-Busbus4: 12Mbps Full Speed USB v1.0 the umass issue.
|
|
I bought a pavillion g6 with an i3-2330m processor
how do i install windows xp on this one???
which is the drivers i need to have??
the site of hp is a chaos
there are so many products under the name of g6!?!?!?!
so far installation stops at the beggining...
Started by anikhtos on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at anandtech):
The graphic card hd3000 crashes the system
h i do not think i will solve this issue Not a solution.
|
|
Hi nerds here,
could i tap your experience?
I have got two pretty similar notebooks.
The first one has got an Atheros AR242x.802.11 abg Ven_168c/Dev_001c/Rev 01 perfectly working.
system profiler sees the Atheros card @ en0
The second one has got an Atheros...
Started by Laszlo Lebrun on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at insanelymac):
Go to ebay and find.
Easiest fix.
Go the PCMCIA airport driver caused an issue on some older atheros.
Easiest fix.
Ive read somewhere the PCMCIA airport driver caused an issue on some older atheros.
|
|
Just a heads up to others. There is a kernel regression in the 2.6.35 kernel with regard to, some but not all Intel Gigabit ethernet adapters using the e1000e driver. After an otherwise successful upgrade from fedora 13 to 14, no ethernet connection could...
Started by kilgoretrout on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at fedoraforum):
I have an Intel ICH8 motherboard....
I am running on an ICH5 from the intel devs about not being able to make the merge window for their ICH8 changes for the 2.6.35 kernel.
Could possibly be the ICH8 chipset motherboards that have the problem.
|
|
I have two computers with an ASRock P5B-DE mainboard, one of them is my primary desktop but the other isn't in use, so I want to try it with PC-BSD, but I was wondering if anyone would know if that would work well.
the system would have this:
Mainboard...
Started by foxofinfinety on
, 4 posts
by 2 people.
Answer Snippets (Read the full thread at pcbsd):
Although this isn't always.
Current hardware + current software =.
That compatibility would not be an issue.
|
