|
I'm looking into getting a cordless compact impact wrench or driver. Which do you guys use? My buddy has the snap on that is ridiculously powerful and expensive, so of course i want one too, however he's a mechanic so he can justify spending $350-$400...
Started by mattman320 on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at fullsizebronco):
Impact wrench is the only friday deals this week....
I agree.
Get a 1/2" to 3/8" adapter bolts into wood but are pretty worthless for working on cars/trucks .
Go with a craftsman impact wrench.
I have years of experience with this.
|
|
Will a 1/2 impact wrench do any damage to kart wheel nuts or hubs as this 1/2 impact wrench http://www.ukhs.tv/24V-Cordless-Square-Drive-Impact-Wrench-Kit has the same spec as this 3/8 impact wrench http://www.sealey.co.uk/PLPageBuilder.asp?gotonode=DoProductSearch...
Started by pk racing on
, 12 posts
by 10 people.
Answer Snippets (Read the full thread at karting1):
|
|
New Craftsman 3/8″ Compact Cordless Impact Wrench:
http://toolguyd.com/craftsman-cordle...-wrench-32741/
The new Craftsman impact wrench features a 3/8″ square drive with anvil retention ring, variable speed 0-2500 no-load RPM gearbox, 130 ft-lbs torque...
Started by homesale on
, 11 posts
by 6 people.
Answer Snippets (Read the full thread at garagejournal):
I do prefer impact and ....
I do prefer the in-handle batteries on 3/8 impacts as they fit torque figure but the battery pack looks pretty big for a 3/8 'compact' impact wrench.
For a 3/8 'compact' impact wrench.
|
Ask your Facebook Friends
|
Okay here's the deal. I have an old Blue Point AT-500c 1/2 twin hammer impact wrench that I bought new back when spinning wrenches was my bread and butter. Now it's just a hobby... I was without a compressor of my own, or even access to one for about ...
Started by dbhost on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at f150online):
The drive of any air tool is fairly when their stuff works as well as higher cost tools, but in the case of impact wrenches, they don't cut with my nailers anyway....
On a impact) it may be just gummed up inside and need a good cleaning.
|
|
I have a small Hitachi impact wrench as some on here know. But needed something a bit more beefy for a crank pulley bolt, so borrowed one of these... http://www.easupplies.com/INGERSOLLRAND-W360KL2-Cordless-Impact-Wrench-Kit-p/pt11bc.htm
...from a mate...
Started by Darth Loo-knee on
, 15 posts
by 6 people.
Answer Snippets (Read the full thread at omegaowners):
Http://www.easupplies.com/INGERSOLLRAND-W360KL2-Cordless-Impact-Wrench-Kit-p/pt11bc.htm: from: chrisgixer on 28 January....
|
|
Do I need a air impact wrench to remove my drive shaft? Can't get off by a regular wrench? I need to replace my Transmission Tailshaft Seal on my 99 Ford Explorer 4.0 OHV with 145k,miles. My question Do I need a air impact wrench to remove my drive shaft...
Started by Mr Wilkinson on
, 8 posts
by 8 people.
Answer Snippets (Read the full thread at yahoo):
All you need to do is to remove the saddle clamps on the rear u-joint, pry the u-joint Impact not needed....
You don't NEED an impact wrench, as long no impact wrench.
As long as you don't run it low on fluid it should be OK .
|
|
I tried to take the old rear shocks of my '86 Carrera. They are the original shocks and have been on the car for 26 years. The lower bolts will not move using just a ratchet. Do you guys use impact wrenches, just soak it in Kroil, use a long pipe extension...
Started by Autoban on
, 11 posts
by 10 people.
Answer Snippets (Read the full thread at pelicanparts):
It only makes the project if they haven't been....
Cheers !
Phil Use an impact wrench.
Typically I only use that I am able to! Air tools here too .. .
In terms of taking off bolts like that, I never use an impact wrench.
Of it.
|
|
Description
$150
Bare-Tool Milwaukee 2663-20 18-Volt M18 1/2-Inch High Torque Impact Wrench with Friction Ring
The M18 cordless 1/2-inch high-torque impact wrenches provide industry-leading power in a compact size. Built with a Milwaukee four-pole motor...
Started by tbst on
, 15 posts
by 8 people.
Answer Snippets (Read the full thread at toyota-4runner):
I used it? I am thinking about....
Good to know.
Great tool.
Broke down an entire Sequoia with one.
Either LITHIUM Dewalt impact driver .
Those are $100 a pop.
Auxiliary" Milwaukee tools, like the sawzall, impact wrench, hole saw, etc.
Related shopping results:
|
|
Ok i need your help. sears has a sale that ends today so i don't have much time. i need an impact wrench/driver for removing the bolts on my mower blades and then putting them back on after sharpening. up to this point i've just been doing it with a socket...
Started by JasonsLawnCare1 on
, 5 posts
by 4 people.
Answer Snippets (Read the full thread at lawnsite):
I need an impact wrench/driver f
so my question is what is the difference in the impact wrench and the impact driver? which one is best for removing/tightening mower blades? i'm is for nails and screws....
Have much time.
|
|
We are running another special on AIRCAT. This is the good one that everyone asked me about last time.
This is the KEVLAR model with 900+ ft/lbs. It weighs about 4lbs. The last time we ran AIRCAT I had a lot of requests after they were gone.
Doing the...
Started by roarksupply.com on
, 13 posts
by 2 people.
Answer Snippets (Read the full thread at pirate4x4):
These prices won't.
With the blanket deal, these are a steal!
Make Sure to use the Code: GRIT Aircat 1100k Kevlar Impact Wrench
[IMG PBB members need an impact? We are almost sold out again and its only tuesday.
|
