|
Okay so i have heard that the fabtechs six inch lift kit is really 8 inches. im looking for a 8 inch lift . should i just get the six inch lift or should i get there 8 inch lift even though its a lot more expensive. im on a budget but want 8 inches of...
Started by crftruck on
, 12 posts
by 7 people.
Answer Snippets (Read the full thread at gmfullsize):
With the bilteins you can be at 9" and have decent angles, i kno you said 8" but that extra inch may.
|
|
Do most of you hunt with 5 inch or 4 inch helical feathers?
Started by eyedoc on
, 32 posts
by 22 people.
Answer Snippets (Read the full thread at texasbowhunter):
And sometimes I use the 5 inch banana cut Either is fine as long as your used to bond it would make it ....
Old school I think the main reason I use 4 with three 5 inch shield...
5 inch.
West texas cosmic cowboy right there for sure.
|
|
Rossi M92 .357 16 inch vs. 20 inch barrel?
I have decided to get a Rossi M92 .357 carbine. My only questions are:
1. Whether to get the 16 inch "trapper" model or 20 inch barrel rifle?
2. Whether the large loop or regular loop is the best purchase?
Thanks...
Started by DavidB2 on
, 14 posts
by 11 people.
Answer Snippets (Read the full thread at thehighroad):
The 20 inch version easily....
Note that the 16 inch model hold 10 rounds of .38Spl either or I would have bought the 16 inch model for my Cowboy Action shooting.
When the backs of them slams into the metal when cycling the gun quickly .
|
Ask your Facebook Friends
|
Is there anything out there that will cut a 1 inch hole in 1/2 inch metal that will chuck into my drill press. I don't have a 1 inch drill bit but was hoping some kind of hole saw is out there for metal. Any help is appreciated.
Started by kctgb on
, 17 posts
by 13 people.
Answer Snippets (Read the full thread at weldingweb):
Even with the carbide....
There are three ways I have done with straight steel .
Can handle metal up to like 1 1/2 inch thick.
A half inch shouldn't be a problem, keep milling devices.
Steel and I've been pleasantly surprised how well they did .
|
|
I have an XI and I was wondering if theres any effect over a half inch from front and rear wheels to an inch?
I know my tires will be 235/35 and 265/30.
Will it be better to have 8 inch in the front and 9 in the rear? Or 8 1/2 in the front and 9 in the...
Started by ZhengHai on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at e90post):
But just to be safe I think I'm going to keep it under 1% .
I have.
It doesn't matter.
If you can choose, get 1 inch difference with those tires.
Listed are fine.
|
|
19 inch versus 24 inch monitors?
I currently use a Planar PX191 19 inch monitor, along with a Viewsonic 17 inch monitor set up as a second monitor. The Planar is a nice monitor, although not particularly known for photo editing. I was reading about 2...
Started by Peter Mendelson on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at openphotographyforums):
I use 2x DELL 20" ones....
OTOH, I would probably opt for saving a bit longer and getting one of them 30" :-)
Cheers! Peter,
A 24" LCD monitor is definitely recommended .
If I had funds for it, I would not hesitate getting one .
Peter,
in two words: it does.
|
|
Why did I get a 5 inch sub when I asked for a 6 inch at Subway? The 6 inch sub my wife bought was longer than my "6 inch" sub. This is not the first time I've noticed the short cut. I usually eat a foot long because I know I'll get gipped. Even when seeing...
Started by Greg Anderson on
, 12 posts
by 12 people.
Answer Snippets (Read the full thread at yahoo):
Your should have been 1 inch with extra cheese dick You should complain before they put.
It accordingly.
|
|
I wanted to get some opinions on sheeting over existing 1/2 inch drywall on the ceiling with 5/8 inch. The ceiling joists are at 24 inches OC and the existing 1/2 inch drywall is sagging between the joists. There was popcorn on the 1/2 inch (why, I don...
Started by Wopadoodle on
, 19 posts
by 16 people.
Answer Snippets (Read the full thread at garagejournal):
You could probably use furring strips to either pull the sagging drywall up or prevent the sagging from telescoping to the new ... .
That stuff is heavy and you can only support so much of it .
Why? Then you will have 1 1/8" sagging drywall, or maybe worse .
|
|
93-96 fleetwoods with 1 inch or 1 1/2 inch extended a arms post pics of you fleetwoods with 1 inch or 1 1/2 inch extended a arms locked or layed out with your extention posted looking to make my mind up on my ride DEATH BEFORE DISHONOR
Missouri's only...
Started by NvSmonte on
, 13 posts
by 10 people.
Answer Snippets (Read the full thread at layitlow):
IMG353.jpg
IMG354.jpg
Down, not really bulldoggin hard huh?
IMG366.jpg I want candy.
Wheels an inch or so..
I did mine 1 inch and its just right, has a little bulldog look to it but nothing too wild.
|
|
Will this work in the front. or will it be too low that i will not be able to turn the wheels. my wheels are about 1 inch smaller than stock. i check and its about 5 inches of space between the wheel and the fender. what about when making left or right...
Started by diego89 on
, 19 posts
by 5 people.
Answer Snippets (Read the full thread at astrosafari):
Maybe tomorrow ill finish both sides Diego, is a 4 inch drop in the front not to radical ??
You could use 2 inch dropped spindles....
Jim My Cup is neither half.
Keep us posted with pix, OK.
Are going to do a 4 inch drop up front? Wow.
|
