|
Pulled the trigger and sent my check to Servicesales for my new Appalachian 52 BAY. I hope to get it before we run out of cold weather to give it a try. Will update this thread on how the install goes and my thoughts on the insert.
Not to many reviews...
Started by mellow on
, 25 posts
by 5 people.
Answer Snippets (Read the full thread at hearth):
Saw://www.servicesales.com/appalachian-stove-parts-c-17.html Current Heater:
Appalachian 52 Bay Insert - My to try a cat
Craft ....
Insert - Had to try a cat
Craft Stove Insert - Old smoke dragon, gotta start somewhere.
Related shopping results:
|
|
Hi guys
Can anyone tell me this. I am installing a new multi-fuel stove. The chimney has an existing ceramic flue liner, is it really necessary to install a new flexible flue liner to it attached directly to the stove pipe or am I OK just inserting the...
Started by flynnboy on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at boards):
Once the stove pipe is inserted into the existing flue without any need a soot door ....
The stove spigot will be about 200mm and is back to back with a neighbours.
insert the 90 degree elbow bend into the stove spigot.
|
|
Hello,
I am planning to heat 3000 square foot home , two stories. I think reasonably insulated. I put R30 in the attic myself, don't know what is in the walls. The house was built in 1979 so I assume insulated with whatever was normal at the time. I don...
Started by Psirusas on
, 12 posts
by 8 people.
Answer Snippets (Read the full thread at hearth):
The footprint of the PH or any other....
I posted now having a healthy discussion with my wife about whether to go with stove or insert.
The stove would be in a 26 x 13 room 8 foot ceilings install into existing fireplace.
Drafts.
|
Ask your Facebook Friends
|
If you are getting smoke in the house or you stove just don’t seem to be burning like should.
Check the door seal and latch for a tight fit.
Check the ash pan for shut tight and latched
If all doors seals are good and latched.
MOST pellet stove are Negative...
Started by poplarchick on
, 18 posts
by 11 people.
Answer Snippets (Read the full thread at hearth):
Http://www.hearthtools.com/install/dirty_insert/index.htm - Basement....
Venting an pellet insert
ALWAYS vent a pellet insert with Stainless steel pipe from the stove all that was not installed with pipe all the way up.
|
|
I have a Lange 911W Wood Cook Stove that I would like to sell but have no idea where to place the value. This stove was in my grandparents kitchen but was never hooked to a chimney and has never had a fire burned in it. It is very clean and I only say...
Started by jbmurt on
, 24 posts
by 10 people.
Answer Snippets (Read the full thread at hearth):
Sure wish I could keep this myself but it has to go Attached Files: Lange911W scan.jpgNo idea....
Osburn 2400 Insert
(sold) Napoleon 1101 with this stove.
Good luck with it.
That thing looks beautiful.
That is an awesome stove.
|
|
Heating season is finally over here in the plains of Eastern Montana the grass is green, the wind is blowing, etc.
Here is the impact on my heating bill after installing a new stove in mid December and an air-source heat pump last May. compared to last...
Started by MTMike on
, 22 posts
by 12 people.
Answer Snippets (Read the full thread at hearth):
Than a boring propane furnace Stay warm and safe,
Steve
Buck Stove 26000 insert (1982, in the living burned the first 18-20% before the install of the stove, and the remaining 5-7% during the rest 1200-1500/year on heating....
|
|
I took out my Earth Stove 906/1002 last year. I was thinking about selling it. My cousin bought it in about 1984 or so. It is a not-cat but has a baffle in it. It has a glass door and swings from the side.
When I began burning wood it saved a lot on the...
Started by ditchrider on
, 22 posts
by 7 people.
Answer Snippets (Read the full thread at hearth):
So do install the window MMech talks it is not legal....
It and your Earth stove are worth eight cents a pound.
Threads/rangeley-install-pics.72432/#post-914628
Earth Stove Thread with pics of the work needed: http a cold one.
|
|
Hi,
We're hoping to build this year (tried last year and didn't happen). The house will be either SIP or conventional framing with cellulose and exterior rigid board. We'll have in-floor radiant on the main floor. Loft will be HWBB. Total sqft is 2100...
Started by jzinckgra on
, 16 posts
by 10 people.
Answer Snippets (Read the full thread at hearth):
We have a pellet stove in our goes out, I'd like to be able to still....
Wood is a pain, especially as you get older.
Harman or P68 pellet stove.
Wood is a pain, especially as you get older.
I'd go with a Harman P61 or P68 pellet stove.
|
|
Hello...
This is my first post here.. I have been doing up a place for a while now and I am about to put the stove in... I had a friend that was a plumber and he was going to help me.. However he passed away last week.
He gave me a list of things to get...
Started by purplemer on
, 15 posts
by 4 people.
Answer Snippets (Read the full thread at ultimatehandyman):
Oh on how to connect the pipe to ....
Then all is clear, it's a combi nation cylinder.
'He's connecting a combi onto a stove!!???'.
You need a pro to install, so lets see the details and we'll go from there.
Is the stove details.
|
|
Hi all,
I just bought my first home... an 1800 sq ft ranch in central NJ. The house was built in 1957 and has baseboard hot water heated by an oil boiler. That boiler is original and huge, probably weighs a ton, but has been very well maintained over ...
Started by jeffesonm on
, 11 posts
by 7 people.
Answer Snippets (Read the full thread at hearth):
An insert has all the ambiance and warmth of an open fire, with the added benefit of actually heating ....
From an insert in the basement, I can't move enough heat from the first floor to the second floor, and that's with an open stairwell.
|
