|
I'm at the crossroads of a big decision and would very much appreciate any input I receive from the group. I will be buying a Wrangler in the next month or two, and cannot decide between a 4dr (Sahara), or a 2dr (Rubicon). Obviously these are questions...
Started by brycec on
, 11 posts
by 9 people.
Answer Snippets (Read the full thread at jeepforum):
Two....
Are you looking for strictly new JK? Would you perhaps consider a 1-2 year old JK Unlimited Rubicon? The reason I ask is cuz I think you could possibly pick up a lightly JK Rubi for under $25K.
Thoughts while reading your post.
|
|
What are the advantages and disadvantages of using *mod_jk* and *mod_proxy* for fronting a tomcat instance with apache?
I've been using mod_jk in production for years but I've heard that it's "the old way" of fronting tomcat. Should I consider changing...
Started by cherouvim on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
Not support Domain model clustering
mod_jk
* Pros: o Advanced load balancer o Advanced node failure.
|
|
Hi,
I am trying to configure mod_jk to forward requests to my webapp running in tomcat. ( I read else where that mod_proxy_ajp is the way to go but want to get this figured out first). I am new to tomcat and mod_jk.
I try to access -- http://www.example...
Answer Snippets (Read the full thread at stackoverflow):
Under heavy load, mod_jk performs better because the mod....
Did you load the module?
LoadModule jk_module [path to it]
The directive will be true should have one entry like this,
JkMount /test/* A
I used both mod_jk and mod_proxy_ajp.
|
Ask your Facebook Friends
|
I needed to front tomcat with apache on AIX, but there is nothing in http://www.apache.org/dist/tomcat/tomcat-connectors/jk/binaries/aix and googling around was unsuccessful. I eventually built it from source (painful as there is bureaucracy around getting...
Started by David Plumpton on
, 4 posts
by 4 people.
Answer Snippets (Read the full thread at stackoverflow):
And support for the mod_jk project seems to have diminished since the introduction of mod_proxy_ajp into the main source of apache-2.2
This modules performes basically the same functionality as mod_jk.
|
|
If I have mod_jk set up with several workers and a load balancer worker, is there a request parameter or something that would allow me to force a specific http request down to a specific worker. For instance if I have a worker worker1 is there something...
Started by polarbear on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
SetEnvIf REQUEST_URI ^/.*\?.*worker=(\w+)&?$ JK_WORKER_NAME=$1 </Location>.
|
|
We have a setup where we have one httpd (apache) with mod_jk talking in a load balance setup to three tomcat servers. We have to recycle each tomcat instance envery three hours. So tomcat1 will restart at 1, and tomcat2 at 2 and ... until tomcat1 recycles...
Started by Geo on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
<Location /jkmanager/> JkMount jkstatus order deny,allow.
Mod_jk re-reads workers.properties on an "apachectl graceful", so you if your workers.properties the jkmanager for mod_jk module.
|
|
I tried googling and the only articles I found comparing these two were from 2005 down to 2002. I just set up my first Tomcat instance to run Jira for a project I'm doing. I want to proxy this through port 80 and apache. From what I can tell, I can easily...
Started by brad on
, 5 posts
by 5 people.
Answer Snippets (Read the full thread at serverfault):
Mod_jk opens which will forward only regular headers across while *mod_jk* would function as a special connector be drawn to scgi and fastcgi connectors....
Mod_proxy will truely "proxy" all requests to tomcat using the normal http connectors .
|
|
Hi all,
I'd setup Apache 2.2 with Mod_Jk so that all Tomcat 6 pages is piped through Apache, port 80. Everything work fine, all pages look good.
My question is: How can I close the port 8080 listened by Tomcat ? Since right now all pages are served from...
Started by SYMPLIK on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at stackoverflow):
Typically it would look something like:
<Connector port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" />
Comment... .
In Tomcats' server.xml file , you are going to want to comment out the connector that references port 8080 .
|
|
Our setup is to have two front-facing WWW servers using Apache1.3 and mod_jk and two application servers running Tomcat. The frontend servers load balance transparently using sticky_sessions.
However, occasionally we need to check one particular backend...
Started by Jeff Bowman on
, 3 posts
by 3 people.
Answer Snippets (Read the full thread at serverfault):
After doing.
Hi,
just change your mod_jk configuration and remove one tomcat from the cluster.
|
|
Hey everyone,
John from Off Road Warehouse was here a while ago putting the Baja Designs Squadron Jeep JK kit on his Jeep, check out this video comparing the Jeep JK stock headlights vs. the Baja Designs JK Kit. If you have any questions please feel free...
Started by BajaDesigns on
, 1 posts
by 1 people.
Answer Snippets (Read the full thread at pirate4x4):
|
